Honda Miimo HRM310 Owner'S Manual Download

Page: 83 / 88

Technical tips

Control panel

Top and
sides

Charging socket

Blades and blades disc

Rear (drive) wheels

Front (caster) wheels

Remove dirt and grass from the following areas:

Mowing mode

You can select from 2 modes of operation (available in “Menu Settings”).

Auto mode (

page 31)

The lawn mower automatically mows according to inputted time and lawn settings.

Manual mode (

page 38)

Start mowing anytime without timer settings.

Cleaning the lawn mower (

page 64)

Clean dirt and grass off of the lawn mower using a dry brush
and cloth.

NOTE:

- Do not clean the lawn mower

with solvent, a pressure
washer, garden hose, etc.

Put on “Paused” (Push the power button

and close the panel cover) state for work so

you can start operation at your desired time.

Regularly check the lawn mower

for assurance.

Store properly for next use.

• Adjusting the height of the

blades (

page 57)

• Checking the “Paused” state

(

page 54)

• Checking the docking station

connections (

page 53)

• Checking the standby status

(

page 54)

• Checking the docking station

• Checking the parts

(

page 63, 65)

• Cleaning and replacing the

blades (

page 70)

• Cleaning the lawn mower

(

page 64)

• Cleaning the docking station

(

page 66)

• Disconnecting the transformer

and power cable (

page 53)

Paused

Weekly check

Storage

Summary of Contents for Miimo HRM310

























































































Search results

Summary of Contents for Miimo HRM310

Reviews:

Related manuals for Miimo HRM310

Brands by name

Popular brands

Honda Miimo HRM310, Owner'S Manual

Search results

Summary of Contents for Miimo HRM310

Reviews:

Related manuals for Miimo HRM310

Brands by name

Popular brands