Honda Miimo HRM310 Owner'S Manual Download

Page: 66 / 88

Maintenance procedures

Preparing

Perform the following procedures in an
area not subject to rainfall.

• Put on a pair of work gloves.
• When checking the blades, turn the lawn

mower on its side.

• Do not tilt the lawn mower over an angle

of 90 degrees to prevent grass clippings

uid from entering inside the lawn

mower.

Correct

90 degrees
or less

Incorrect

More than 90
degrees

Cleaning

WARNING

- Do not touch the blades with your hands.
- Do not lift the lawn mower off of the ground while checking or cleaning it.
- Make sure to press the manual STOP button and turn the lawn mower off before performing the

following procedures.

NOTE:

- Do not wash the lawn mower with water. The lawn mower may be damaged.

Cleaning the body (Exterior)

Clean dirt and grass off of the lawn mower using a dry brush and
cloth.

Control panel

Top and sides

Charging socket

Removing the grass clippings

By using a dry brush or scraper, remove grass clippings attached to the blades, driving part and water drain

holes.

NOTE:

- Never pour water on the bottom of the lawn mower, and avoid using a sponge or rag soaked with water for

cleaning the lawn mower. The lawn mower may be damaged if water or dirt, such as grass clippings, enter

inside of the lawn mower through the drain holes or gaps.

Rear (drive)
wheels

Front (caster) wheels

Blades and
blades disc

Drain holes

Summary of Contents for Miimo HRM310

























































































Search results

Summary of Contents for Miimo HRM310

Reviews:

Related manuals for Miimo HRM310

Brands by name

Popular brands

Honda Miimo HRM310, Owner'S Manual

Search results

Summary of Contents for Miimo HRM310

Reviews:

Related manuals for Miimo HRM310

Brands by name

Popular brands