Honda Miimo HRM310 Owner'S Manual Download

Page: 56 / 88

Connecting to a power source / Checking the lawn mower / Turning on / off the power

Attach the connector cover to the station.

(The power cord and boundary wire should go through the notch in the
connector cover.)

Power cord

Transformer

Connect the power cord and the transformer connectors.

NOTE:

- When disconnecting the connectors, make sure to lift the clip.

Connect the transformer plug to a power outlet with the designated voltage.

Checking the lawn mower

Before operation, check to make sure that it is connected all the way into the docking station.

The LED light above the charging plug changes as follows:

Color

Description

Green

The docking station signal setting is correct.

Green

(blinking)

The boundary wire is too long.

Amber

The lawn mower is correctly connected to the

docking station.

Amber

(blinking)

A signal problem—such as the boundary wire

becoming disconnected or cut—has occurred.

Contact your dealer.

Red

Contact your dealer.

Off

Con

rm the connection with the power cord.

If the docking station is correctly connected

with the power cord, a power failure has

occurred. Contact your dealer.

NOTE:

- If the lawn mower is not correctly connected to the docking station, the battery cannot recharge.
- Do not touch the recharging connector. If you touch it, you may be injured.

Turning on / off the power

Turning on the power

After the battery is charged, press the

(On) button to turn on the lawn mower.

The

(On) button is located on the control panel at the rear side of the lawn mower.

WARNING

- Do not insert your

nger beneath the closed operation panel cover or height adjustment dial cover.

- When stopping the lawn mower, approach it from the back. Approaching it from the front or sides

may lead to unintended contact with the lawn mower, and you may fall over it when the lawn mower
begins to move.

Press the manual STOP button.

The control panel cover pops up.

Summary of Contents for Miimo HRM310

























































































Search results

Summary of Contents for Miimo HRM310

Reviews:

Related manuals for Miimo HRM310

Brands by name

Popular brands

Honda Miimo HRM310, Owner'S Manual

Search results

Summary of Contents for Miimo HRM310

Reviews:

Related manuals for Miimo HRM310

Brands by name

Popular brands