background image

83

Exclusions:

1. 

Any damage or deterioration resulting from the following:
- Neglect of the periodic maintenance as speci

fi

 ed in the product owner’s manual 

-  Improper repair or maintenance
- Operating methods other than those indicated in the product owner’s manual
- Increasing engine speed beyond factory speci

fi

 cation

- The use of non-genuine Honda parts, accessories, lubricants, and 

fl

 uids other than those approved by Honda

-  Exposure of the product to soot and smoke, chemical agents, bird droppings, sea water, salt, or other 

corrosive environments

-  Collision, fuel contamination or deterioration, neglect, unauthorized alteration, misuse, incorporation or use of 

unsuitable attachments or parts

-  Normal wear and tear (including, but not limited to, normal fading of painted or plated surfaces, sheet peeling, 

and other natural deterioration)

2. 

Consumable parts: Honda does not warrant parts deterioration due to normal wear and tear. The following parts 
are not covered by this warranty unless they are needed during another repair covered under this warranty: 
spark plug, fuel 

fi

 lter, air cleaner element, clutch disc, tire, wheel bearing, recoil starter rope, cable, belt, cutter 

blade, boundary wire, bushings, oil, and grease.

3. 

Cleaning, adjustment, and normal periodic maintenance work (carburetor cleaning, engine oil draining, blade 
sharpening, belt and cable adjustments).

4. 

Any product that has ever been declared a total loss or sold for salvage by a 

fi

 nancial institution or insurer.

5. 

Auger and paddle assemblies, skid shoes, and scraper bars of snow throwers/snow blowers, tiller tines of 
roto-tillers, and mower blades and mower deck housings are speci

fi

 cally not warranted against impact damage 

including, but not limited to, abrasive damage.

Disclaimer of Consequential Damage and Limitation of Implied Warranties:

American Honda disclaims any responsibility for loss of time or use of the product, transportation, commercial loss, 
or any other incidental or consequential damage. Any implied warranties are limited to the duration of this written 
limited warranty. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the 
exclusion or limitation of incidental or consequential damages, therefore the above exclusions and limitations may 
not apply to you. This warranty gives you speci

fi

 c legal rights, and you may also have other rights, which vary from 

state to state.

Summary of Contents for Miimo HRM310

























































































Reviews: