manualshive.com logo in svg

Hitachi SJ700B SERIES, Instruction Manual

The Hitachi SJ700B SERIES Quick Reference Manual is a valuable resource that provides essential information about the product's features, functionalities, and troubleshooting tips. It can be easily accessed for free download from our website, offering users clear instructions and detailed specifications to enhance their experience with this exceptional product.

Share
Download
background image

Chapter 4 Explanation of Functions

 

4 - 139 

(6) List of registers 
 
The "R/W" column of the list indicates whether the coils and registers are read-only or readable and 
writable. 
"R" indicates a read-only coil or register. "R/W" indicates a readable and writable coil or register. 
 
(i) List of coils 

Coil No. 

Item 

R/W 

Setting 

0000h (Reserved) 

-   

0001h 

Operation command 

R/W 

1: Run, 0: Stop (valid when A002 = 03) 

0002h 

Rotation direction command 

R/W 

1: Reverse rotation, 0: Forward rotation (valid when A002 = 03)

0003h 

External trip (EXT) 

R/W 

1: Trip 

0004h 

Trip reset (RS) 

R/W 

1: Reset 

0005h (Reserved) 

-   

0006h (Reserved) 

-   

0007h 

Intelligent input terminal [1] 

R/W 

1: ON, 0: OFF (*1) 

0008h 

Intelligent input terminal [2] 

R/W 

1: ON, 0: OFF (*1) 

0009h 

Intelligent input terminal [3] 

R/W 

1: ON, 0: OFF (*1) 

000Ah 

Intelligent input terminal [4] 

R/W 

1: ON, 0: OFF (*1) 

000Bh 

Intelligent input terminal [5] 

R/W 

1: ON, 0: OFF (*1) 

000Ch 

Intelligent input terminal [6] 

R/W 

1: ON, 0: OFF (*1) 

000Dh 

Intelligent input terminal [7] 

R/W 

1: ON, 0: OFF (*1) 

000E

ｈ

 

Intelligent input terminal [8] 

R/W 

1: ON, 0: OFF (*1) 

000Fh 

Operation status 

R 

1: Run, 0: Stop (interlocked to "d003") 

0010h 

Rotation direction 

R 

1: Reverse rotation, 0: Forward rotation (interlocked to "d003")

0011h 

Inverter ready 

R 

1: Ready, 0: Not ready 

0012h Unused 

R   

0013h 

RUN (running) 

R 

1: Tripping, 0: Normal 

0014h 

FA1 (constant-speed reached) 

R 

1: ON, 0: OFF 

0015h 

FA2 (set frequency overreached) 

R 

1: ON, 0: OFF 

0016h 

OL (overload notice advance signal (1))

R 

1: ON, 0: OFF 

0017h 

OD (output deviation for PID control) 

R 

1: ON, 0: OFF 

0018h 

AL (alarm signal) 

R 

1: ON, 0: OFF 

0019h 

FA3 (set frequency reached) 

R 

1: ON, 0: OFF 

001Ah 

OTQ (over-torque) 

R 

1: ON, 0: OFF 

001Bh 

IP (instantaneous power failure) 

R 

1: ON, 0: OFF 

001Ch 

UV (undervoltage) 

R 

1: ON, 0: OFF 

001Dh 

TRQ (torque limited) 

R 

1: ON, 0: OFF 

001Eh 

RNT (operation time over) 

R 

1: ON, 0: OFF 

001Fh 

ONT (plug-in time over) 

R 

1: ON, 0: OFF 

0020h 

THM (thermal alarm signal) 

R 

1: ON, 0: OFF 

0021h (Reserved) 

-   

0022h (Reserved) 

-   

0023h (Reserved) 

-   

0024h (Reserved) 

-   

0025h (Reserved) 

-   

0026h 

BRK (brake release) 

R 

1: ON, 0: OFF 

0027h 

BER (brake error) 

R 

1: ON, 0: OFF 

0028h 

ZS (0 Hz detection signal) 

R 

1: ON, 0: OFF 

0029h 

DSE (speed deviation maximum) 

R 

1: ON, 0: OFF 

002Ah 

POK (positioning completed) 

R 

1: ON, 0: OFF 

002Bh 

FA4 (set frequency overreached 2) 

R 

1: ON, 0: OFF 

002Ch 

FA5 (set frequency reached 2) 

R 

1: ON, 0: OFF 

002Dh 

OL2 (overload notice advance signal 
(2)) 

R 

1: ON, 0: OFF 

002Eh 

Odc: Analog O disconnection detection 

- 

 

002Fh OIDc: 

Analog 

OI 

disconnection detection

- 

 

0030h 

O2Dc: Analog O2 disconnection 
detection 

-  

0031h (Reserved) 

-   

0032h 

FBV (PID feedback comparison) 

R 

1: ON, 0: OFF 

0033h 

NDc (communication train 
disconnection) 

R 

1: ON, 0: OFF 

0034h 

LOG1 (logical operation result 1) 

R 

1: ON, 0: OFF 

Summary of Contents for SJ700B SERIES




















































































































































































































































































Reviews:

No comments

Related manuals for SJ700B SERIES

Harmonic Electra 9200 Getting Started Manual preview
Electra 9200
Brand: Harmonic Pages: 27
Wacker Neuson G 240 Operator'S Manual preview
G 240
Brand: Wacker Neuson Pages: 254
APsystems DS3 Series Installation & User Manual preview
DS3 Series
Brand: APsystems Pages: 24
Lenze ETW-i700-C01 Manual preview
ETW-i700-C01
Brand: Lenze Pages: 28
Manhattan 151047 Instructions preview
151047
Brand: Manhattan Pages: 2
ASEA AC55LC-3 Operation Manual preview
AC55LC-3
Brand: ASEA Pages: 75
JRC NJU26209 Manual preview
NJU26209
Brand: JRC Pages: 10
Ableconn VGA2HDMIB User Manual preview
VGA2HDMIB
Brand: Ableconn Pages: 15
Saftronics CIMR-VG5U Installation & Quick Start Manual preview
CIMR-VG5U
Brand: Saftronics Pages: 113
YASKAWA PVI 36TL Installation And Operation Manual preview
PVI 36TL
Brand: YASKAWA Pages: 120
Pulsar DC/DC20SD Quick Start Manual preview
DC/DC20SD
Brand: Pulsar Pages: 4
C4i CV-53BI User Manual preview
CV-53BI
Brand: C4i Pages: 9
ADF Web HD67668-A1 User Manual preview
HD67668-A1
Brand: ADF Web Pages: 25
Kramer 840Hxl User Manual preview
840Hxl
Brand: Kramer Pages: 30
Odorox BOSS XL3 Manual preview
BOSS XL3
Brand: Odorox Pages: 11
TA D-LOGG Manual preview
D-LOGG
Brand: TA Pages: 32
IONODES ION-E100-HD User Manual preview
ION-E100-HD
Brand: IONODES Pages: 23
Autarco S2.UX40000 Installation And Operation Manual preview
S2.UX40000
Brand: Autarco Pages: 37

Brands by name

Popular brands

Load more brands