manualshive.com logo in svg

Hitachi SJ700B SERIES, Instruction Manual

The Hitachi SJ700B SERIES Quick Reference Manual is a valuable resource that provides essential information about the product's features, functionalities, and troubleshooting tips. It can be easily accessed for free download from our website, offering users clear instructions and detailed specifications to enhance their experience with this exceptional product.

Share
Download
background image

Chapter 4 Explanation of Functions 

 

4 - 112 

4.3.21 Pulse train frequency input 

The pulse train frequency input function allows you to use the 
pulse train input via the SAP or SAN terminal as a frequency 
command or PID feedback data in each control mode. (You 
can use this function in every control mode.) 
Specify the input frequency corresponding to the allowable 
maximum frequency as the pulse train frequency scale 
(P055). 
You cannot use the start/end frequency setting function for external analog input together with this function. 
To limit the input frequency, specify the desired values for the pulse train frequency bias (P057) and pulse   
train frequency limit (P058). 
 

Item 

Function code

Data or range of data

Description 

Pulse train frequency scale 

P055 

1.0 to 50.0 (kHz) 

Specification of the input frequency 
corresponding to the maximum 
allowable frequency 

Time constant of pulse train 
frequency filter 

P056 

0.01 to 2.00 (s) 

Setting of the filter time constant for 
the pulse train input 

Pulse train frequency bias 

P057 

-100. to +100. (%) 

 

Pulse train frequency limit 

P058 

0. to 100. (%) 

 

Frequency source setting 

A001 

06 

PV source setting 

A076 

03 

Operation-target frequency 
selection 1 

A141 05 

Operation-target frequency 
selection 2 

A142 05 

Settings for the frequency input as a 
pulse train 

 
 
 
 
 
 
 
 
 
 
 

Block diagram for pulse train frequency input 

 

P055: Pulse-string frequency scale 
P056: Time constant of pulse-string frequency filter 
P057: Pulse-string frequency bias 
P058: Pulse-string frequency limit 
A002: Frequency source setting 
A076: PV source setting 
A141: Operation-target frequency selection 1 
A142: Operation-target frequency selection 2 

Related code 

÷

 

1+sT 

1 

×

 

 

Hz 

% 

%

Hz 

 

Frequency 
measurement 

Frequency scale 
(1.0 to 50.0 kHz) 

Primary delay filter

 

Maximum 
frequency (F004) 

Bias limitation

 

Limit

 

Bias

 

Frequency 
command 

Summary of Contents for SJ700B SERIES




















































































































































































































































































Reviews:

No comments

Related manuals for SJ700B SERIES

ABB ACS 600 MultiDrive Hardware Manual preview
ACS 600 MultiDrive
Brand: ABB Pages: 94
Canadian Solar CSI-25KTL-GS-FLB Installation And Operation Manual preview
CSI-25KTL-GS-FLB
Brand: Canadian Solar Pages: 53
Icy Box IB-CVB513 Quick Installation Manual preview
IB-CVB513
Brand: Icy Box Pages: 2
Clearline V210 Manual preview
V210
Brand: Clearline Pages: 4
April Music Aura vivid Owner'S Manual preview
Aura vivid
Brand: April Music Pages: 11
Goobay 60267 User Manual preview
60267
Brand: Goobay Pages: 24
Samlexpower PST-1000F-12 Owner'S Manual preview
PST-1000F-12
Brand: Samlexpower Pages: 56
Hoval TopTronic E Solar TTE-SOL Instructions Manual preview
TopTronic E Solar TTE-SOL
Brand: Hoval Pages: 95
DCS Rossini Transport User Manual preview
Rossini Transport
Brand: DCS Pages: 31
D.A.S. DASNET-SPLITTER User Manual preview
DASNET-SPLITTER
Brand: D.A.S. Pages: 12
Digitus DS-40137 Manual preview
DS-40137
Brand: Digitus Pages: 6
SIIG AV-GM01U3-S1 Manual preview
AV-GM01U3-S1
Brand: SIIG Pages: 12
Lindy 43246 User Manual preview
43246
Brand: Lindy Pages: 2
TA D-LOGG Manual preview
D-LOGG
Brand: TA Pages: 32
Lambda LS1291P User Manual preview
LS1291P
Brand: Lambda Pages: 47
Audio Technica AT-DAC100 User Manual preview
AT-DAC100
Brand: Audio Technica Pages: 11
MAER IDROPULITRICI AVANT 120/11 Instructions For Installation And Use Manual preview
AVANT 120/11
Brand: MAER IDROPULITRICI Pages: 48
MG STE02W User Manual preview
STE02W
Brand: MG Pages: 38

Brands by name

Popular brands

Load more brands