Hitachi H8S/2631 Hardware Manual Download Page 602

Page: 602 / 1168

584



Receive error detection : Overrun errors detected

•

Full-duplex communication capability



The transmitter and receiver are mutually independent, enabling transmission and reception

to be executed simultaneously



Double-buffering is used in both the transmitter and the receiver, enabling continuous

transmission and continuous reception of serial data

•

Choice of LSB-first or MSB-first transfer



Can be selected regardless of the communication mode* (except in the case of

asynchronous mode 7-bit data)

Note: * Descriptions in this section refer to LSB-first transfer.

•

On-chip baud rate generator allows any bit rate to be selected

•

Choice of serial clock source: internal clock from baud rate generator or external clock from
SCK pin

•

Four interrupt sources



Four interrupt sources — transmit-data-empty, transmit-end, receive-data-full, and receive

error — that can issue requests independently



The transmit-data-empty interrupt and receive data full interrupts can activate the DMA

controller (DMAC) or data transfer controller (DTC) to execute data transfer

•

Module stop mode can be set



As the initial setting, SCI operation is halted. Register access is enabled by exiting module
stop mode.

Summary of Contents for H8S/2631

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for H8S/2631

Reviews:

Related manuals for H8S/2631

Brands by name

Popular brands

Hitachi H8S/2631, Hardware Manual

Search results

Summary of Contents for H8S/2631

Reviews:

Related manuals for H8S/2631

Brands by name

Popular brands