HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download

Page: 82 / 160

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

User Manual

>>>

N.B.!

•

Before starting fast lowering make sure

that no-one or nothing is under the container.

•

Do not exit the cockpit during the lowering process.

•

If the vehicle is moving while the container is being lowered in fast

speed mode,

- note the height of the hooklift device / container in relation to the surrounding

bridges, tunnels and overhead power lines.

Drive carefully and cautiously.

A rear-heavy container, slanted ground and/or cold oil may prevent the fast

lowering option from being activated.

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands