HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download

Page: 47 / 160

4/2018

Hooklift Multilift XR S

User Manual

113175421

XR14S/16S/18S/21S/26S/30S

Move the hook arm / middle frame together with the container to rearmost

position

- move the control lever slowly backward.

10.

Release the parking brake when the container rear end touches the ground.

Only in case the truck is on uphill slope, you may not release the hand brake, as in

that case the truck and the container would move backwards.

NOTE! In some cases the container will push the truck forward.

Assist this, if necessary, by steering the truck and simultaneously holding the

control lever in backward position.

11.

Stop the movement by letting the control lever free.

12.

Lower the middle frame even lower.

Drive the truck forward so that the hook will be off the container gripping bar.

13.

Engage the parking brake.

14.

Move the hook arm / middle frame to forward position

- hold the control lever in forward position until the frame is completely on the sub

frame.

15.

Move the hook arm forward

- move the control lever to left and forward.

Continue the movement until the frame is in the forward position.

The hooklift equipment is now in transport position.

NOTE! If there is a safety code CXXX and/or dXXX in the display,

then see the chapter ”Safety codes” after the chapter ”Unloading a container”.

The unloading will start in most cases but the reason to the code must be

checked and repaired as soon as possible to avoid any risk to injuries or

damages.

Safety codes >>

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands