manualshive.com logo in svg

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Share
Download
HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download Page 141

141

4/2018 

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

Service Manual

>>>

ERROR CODE

COMMENTS / PROBLEM

LOCATION

PROGRAM DESCRIPTION

POSSIBLE ACTION

CONSEQUENCE

d009

MIDDLE FRAME IS UP (NOT NEARLY DOWN)

MIDDLE FRAME IN WRONG POSITION

d010

MIDDLE FRAME IS DOWN

MIDDLE FRAME IN WRONG POSITION

d011

MIDDLE FRAME IS NEARLY DOWN

MIDDLE FRAME IN WRONG POSITION

d012

REAR FRAME IS UP (NOT DOWN)

REAR FRAME IN WRONG POSITION

d013

REAR FRAME IS DOWN

REAR FRAME IN WRONG POSITION

d014

ARM IS NOT IN BACK POSITION

TELESCOPIC / TILTING ARM IN WRONG 

POSITION

SLIDE / TILT BWD OR CHECK THE  HORIZONTAL 

MOVEMENT BACK SENSOR

d015

ARM IS IN BACK POSITION

TELESCOPIC / TILTING ARM IN WRONG 

POSITION

d016

PULL LIMITER IS ACTIVE

PULL LIMITER IS ACTIVE

SLIDE / TILT BWD OR CHECK THE PULL LIMITER 

SENSOR

NO SLIDE FWD

d017

CRANE BODY IS ACTIVE

CRANE BODY ON IS ACTIVE

SLIDE / TILT BWD OR CHECK THE CRANE BODY 

SENSOR

NO SLIDE FWD

d018

CATCH LOCKING RIGHT ARE ACTIVE

CATCH LOCKING RIGHT ARE ACTIVE

OPEN THE RIGHT SIDE CATCH LOCKING / CHECK 

THE SENSOR

NO HOOKLIFT 

FUNCTION

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands