HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download

Page: 74 / 160

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

User Manual

The correct operation of the safety lock must be checked

regularly and the shaft nipple greased every month.

•

Open the safety lock of the gripping

hook by pressing button on the

control

unit

immediately

before

lowering the front end of the container

the

ground.

•

Stop the main cylinder when the

container reaches the ground.

•

Check that the safety lock is still open.

If the safety lock has closed, it may

cause the safety lock or the gripping

bar to be damaged when the hook is

pressed down on the gripping bar.

•

Continue the downward motion of the

main cylinders, with the safety lock

open, until the hook is released from

the

gripping

bar.

•

Drive the vehicle forward, away from

the

container.

See

section

“unloading”.

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands