HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download

Page: 144 / 160

144

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

Service Manual

>>>

FAULTS

03.00

LOW

ILLEGAL

VOLTAGE

DIGITAL

OUTPUT

(OUTPUT

1 - 4)

DIGITAL OUTPUT

(1-4) HAVE

ILLEGAL VOLTAGE,

EXPECTED LOW

DETECTED AS

HIGH.

ERROR DISPLAYED ON DISPLAY.

04.00

LOW

SHORT

CIRCUIT

ON DIGITAL

OUTPUT

DIGITAL OUTPUT

(1 - 4) SHORT

CIRCUITED OR

OVERLOADED, CAN

BE ANY OF THE 4

OUTPUTS.

ERROR DISPLAYED ON DISPLAY.

08.01

MEDIUM

CAN PASSIVE

CAN BUS IN

PASSIVE MODE.

ERROR DISPLAYED ON DISPLAY, CAN MODULE

SWITCHED TO PRE-OPERATIONAL STATE AND

SYSTEM WILL SELF RESET AUTOMATICALLY.

WAIT, UNTIL THE SYSTEM HAS STARTED.

08.02

MEDIUM

CAN I/O

BUFFER

OVERFLOW

CAN OVERRUN;

EITHER THE CAN

INPUT OR CAN

OUTPUT BUFFER

ARE FULL.

ERROR DISPLAYED ON DISPLAY, CAN MODULE

SWITCHED TO PRE-OPERATIONAL STATE AND

SYSTEM WILL SELF RESET AUTOMATICALLY.

WAIT, UNTIL THE SYSTEM HAS STARTED.

08.03

MEDIUM

CAN

PHYSICAL

LAYER

ERROR

BAD

COMMUNICATION /

TRANSMISSION.

ERROR DISPLAYED ON DISPLAY, CAN MODULE

SWITCHED TO PRE-OPERATIONAL STATE AND

SYSTEM WILL SELF RESET AUTOMATICALLY.

WAIT, UNTIL THE SYSTEM HAS STARTED.

08.04

MEDIUM

CAN

MESSAGE

LENGTH

ERROR

CAN MESSAGE

LENGTH IS TOO

LONG.

ERROR DISPLAYED ON DISPLAY, CAN MODULE

SWITCHED TO PRE-OPERATIONAL STATE AND

SYSTEM WILL SELF RESET AUTOMATICALLY.

WAIT, UNTIL THE SYSTEM HAS STARTED.

08.05

MEDIUM

CAN

MESSAGE

LENGTH

ERROR

CAN MESSAGE

LENGTH IS TOO

SHORT.

ERROR DISPLAYED ON DISPLAY, CAN MODULE

SWITCHED TO PRE-OPERATIONAL STATE AND

SYSTEM WILL SELF RESET AUTOMATICALLY.

WAIT, UNTIL THE SYSTEM HAS STARTED.

08.06

MEDIUM

CAN

TRANSMIT

COLLISION

TO MANY

COLLISIONS ON

CAN-BUS.

ERROR DISPLAYED ON DISPLAY, CAN MODULE

SWITCHED TO PRE-OPERATIONAL STATE AND

SYSTEM WILL SELF RESET AUTOMATICALLY.

WAIT, UNTIL THE SYSTEM HAS STARTED.

ERROR

CODE

1.2

(CATEGORY)

DESCRIPTION CAUSE

ACTION

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands