HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download

Page: 78 / 160

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

User Manual

Switch and signal light of hydraulic body locks

The body locks are opened by pressing the switch in the control unit. A burning lock signal

light on the control unit means that the body locks are not fully closed.

The signal light blinks if the lock hooks are between the open and closed positions.

When in traffic, no driving or tipping is to be commenced if the light is on. Remove the

element obstructing the locks, or if they are obstructed by the lock pocket in the container

frame beam, check that the container is correctly positioned on top of the hook device.

Function

Open body locks

Close body locks

LED comes on

LED off

LEDs

2GCC

Display

and LEDs

2GRC

LEDs

2GMR

Button

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands