HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download

Page: 29 / 160

4/2018

Hooklift Multilift XR S

User Manual

113175421

XR14S/16S/18S/21S/26S/30S

Loading a container

See the safety instructions before loading.

Reverse the truck carefully close to the container.

Stop it about 16 ft (5 m) from the container gripping bar.

Engage the parking brake.

Press the clutch pedal and engage the PTO.

If the truck is equipped with any of the following equipment, do the following:

- retract the adjustable under-run bar (mechanical or manual hydraulic)

- deflate the air suspension

- activate the bogie blocking cylinders or stabilising roller.

Open the hydraulic body locks

- press the “body lock” button

- “locks not closed” signal light lit on the control unit when the locks are open.

Open the mechanical or hydraulic front locks (optional).

Move the hook arm fully rearward position

- move the control lever to left and back.

- mechanical tipping lock will be opened in the rear position of the hook arm.

NOTE! If there is a safety code CXXX and/or dXXX in the display,

then see the chapter ”Safety codes” after the chapter ”Loading a container”.

The loading will start in most cases but the reason to the code must be checked

and repaired as soon as possible to avoid any risk to injuries or damages.

Safety codes >>>

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands