manualshive.com logo in svg

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Share
Download
HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download Page 49

49

4/2018 

Hooklift Multilift XR S

User Manual

113175421

XR14S/16S/18S/21S/26S/30S

16. 

 Close the hydraulic body locks

 

- press the “body locks closed” button

 

Signal light “locks not closed” must go out.

17. 

 If the truck is equipped with any of the following equipment, do the following:

 

- extend the adjustable under-run bar (mechanical or manual hydraulic)

 

- re-inflate the air suspension

 

- release the bogie blocking cylinders or lift up the stabilising roller.

18. 

 Press the clutch pedal and disengage the PTO.

19. 

 Check that all signal lights of the control unit have gone out.

NOTE! If there is a safety code CXXX and/or dXXX in the display,

then see the chapter ”Safety codes” after the chapter ”Unloading a container”.

The unloading will start in most cases but the reason to the code must be 

checked and repaired as soon as possible to avoid any risk to injuries or 

damages.

Safety codes >

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands