HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download

Page: 143 / 160

143

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

Service Manual

>>>

FAULTS
01.01

MEDIUM

EEPROM

FAILURE

ERROR DETECTED

ON NON VOLATILE

MEMORY

ERROR DISPLAYED ON DISPLAY, CAN MODULE

SWITCHED TO PRE-OPERATIONAL STATE AND

SYSTEM WILL SELF RESET AUTOMATICALLY.

WAIT, UNTIL THE SYSTEM HAS STARTED.

01.02

SEVERE

FLASH

MEMORY

FAILURE

INCORRECT

CHECKSUM ON

FLASH MEMORY

ERROR DISPLAYED ON DISPLAY, SYSTEM

SWITCHED TO ERROR STATE.

SYSTEM MUST

BE POWER CYCLED.

01.03

MEDIUM

STACK

MEMORY

FAILURE

INCORRECT

SIZES IN CAN

OPEN PROTOCOL,

INCORRECT

DATAFLOW, OR

STACK OVERFLOW

ERROR DISPLAYED ON DISPLAY, CAN MODULE

SWITCHED TO PRE-OPERATIONAL STATE AND

SYSTEM WILL SELF RESET AUTOMATICALLY.

WAIT, UNTIL THE SYSTEM HAS STARTED.

01.04

MEDIUM

RAM

MEMORY

FAILURE

INCORRECT RAM

AND/OR HARDWARE

IDENTIFICATION

ERROR DISPLAYED ON DISPLAY, CAN MODULE

SWITCHED TO PRE-OPERATIONAL STATE AND

SYSTEM WILL SELF RESET AUTOMATICALLY.

WAIT, UNTIL THE SYSTEM HAS STARTED.

ERROR

CODE

1.2

(CATEGORY)

DESCRIPTION CAUSE

ACTION

Error codes, control unit

POSSIBLE ERRORS INSIDE CONTROL UNIT

WHEN INTERNAL OR COMMUNICATION ERRORS OCCUR ON CONTROL UNIT FOLLOWING DIFFERENT ERROR

CODES ARE DISPLAYED ON THE 7SEGMENT DISPLAYS. THEY ARE DISPLAYED ACCORDING TO THIS SCENARIO:

ERR 1ST -> ERR 2ND

ERROR CATEGORIES

1.2

LOW

INFORMATION SHOWN ON DISPLAY AND CORRESPONDING FUNCTION STOPPED.

1.2

MEDIUM INFORMATION SHOWN ON DISPLAY, AND THEN IS SYSTEM RE-STARTED AUTOMATICALLY

TO REINITIATE SYSTEM CORRECTLY.

1.2

SEVERE INFORMATION SHOWN ON DISPLAY, CAN-BUS DE-ACTIVATED AND SYSTEM LOCKED.

NEEDS POWERCYCLE TO RESTART.

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands