HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download

Page: 88 / 160

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

User Manual

>>>

Bogie blocking

• Optional bogie blocking can be installed on rear axle of the vehicle (6x4 & 8x4). The

stabilizer supports the vehicle substantially during loading operation and when

unloading to the ground.

• The stability of vehicles is worse on new vehicles due to lower weight and greater

load capacity.

The bogie blocking cylinders are used by the control unit switches which control the

additional valve installed in the directional valve configuration.

•

Automatic bogie blocking

When the body locks are opened, the directional control valve on the bogie blocking

cylinders is adjusted to switch on the bogie blocking cylinders; once the body locks

are closed, also the bogie blocking cylinders are released.

Attention! Bogie blocking should never be used during tipping.

If the XR equipment has an adjustable under-run bar, the signal light of additional

equipment is used as a signal light of bogie blocking.

Operating

the bogie blocking

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands