Revision C • 1/04
H
A
R
R
I
S
C
O
R
P
O
R
A T
I
O
N
3-7
3 Operation
digital
FADER SECTION
This section has the Input Source Display; input Source Selector and Take controls;
Telco Monitor and Record Feed assignment buttons; the Talkback, Solo, Cue, On,
and Off buttons; and the signal level fader.
Input S
Input S
Input S
Input S
Input Sour
our
our
our
ourc
cc
cce D
e D
e D
e D
e Displa
ispla
ispla
ispla
isplay —
y —
y —
y —
y —
A two-line ten-character display that shows the
module’s name in the top line (TELCO 1). When the input is a Switcher, as shown in
the full module illustration, the top line shows the current source (SAT_FEED) and
the bottom line shows the selected source (NEWS_1).
S
S
S
S
Sour
our
our
our
ourc
cc
cce S
e S
e S
e S
e Selec
elec
elec
elec
electttttor —
or —
or —
or —
or —
A rotary encoder to scroll through the available VistaMax,
router or Ext. RLS sources (shown in the Display’s bottom line). Only active when
the module is set as a Switcher (see page 2-25 for DIP switch settings).
T
T
T
T
TAKE —
AKE —
AKE —
AKE —
AKE —
When pressed, “takes” the selected source shown in the display’s bottom
line. This makes it the current source, thus its name will be shown in both the top
and bottom lines. The Take button and Source Selector are only active when the
module is set as a Switcher (see page 2-25 for DIP switch settings).
T
T
T
T
TO REC —
O REC —
O REC —
O REC —
O REC —
When lit solid, adds the module’s audio to the Telco record output.
When flashing, indicates the module is not feeding the record output (see pages 3-
9 and 3-10 for additional information on this function). To select or deselect this
button, the FCN
FCN
FCN
FCN
FCN button must be lit (see below).
FCN —
FCN —
FCN —
FCN —
FCN —
Function button. Press for a full second to light, then press the TTTTTo Rec
o Rec
o Rec
o Rec
o Rec or TTTTTo Mon
o Mon
o Mon
o Mon
o Mon button to
change the setting. The TTTTTo Rec
o Rec
o Rec
o Rec
o Rec and TTTTTo Mon
o Mon
o Mon
o Mon
o Mon buttons can only be changed while the FCN
FCN
FCN
FCN
FCN button is lit.
T
T
T
T
TO MON —
O MON —
O MON —
O MON —
O MON —
When lit, adds the module to the Telco monitor mix that is available on the Control Room
and Studio modules. To select or deselect, the FCN
FCN
FCN
FCN
FCN button must be lit (see above).
T
T
T
T
TALKB
ALKB
ALKB
ALKB
ALKBA
A
A
A
ACK —
CK —
CK —
CK —
CK —
A momentary press to talk button so the board operator can to talk to the caller or
remote on the left output of that Telco Input’s mix-minus output.
SOL
SOL
SOL
SOL
SOLO —
O —
O —
O —
O —
When lit, adds the module’s post-fader audio to the Solo bus and interrupts the monitor and
operator headphone outputs, but does not affect the on-line signal, the co-host or guest outputs. Solo can
be a momentary or a latched function, following a Session module DIP switch setting (page 2-33).
CUE —
CUE —
CUE —
CUE —
CUE —
When lit, routes the module’s pre-fader, pre-switch audio to the Control Room module’s cue
output. This does not affect the on-line signal.
F
F
F
F
Fader —
ader —
ader —
ader —
ader —
A 100mm module level control with dB indications along the left side to show relative
attenuation. Set the fader to the red reference line (-12 dB) for module unity gain. This means a nominal
+4 dBu analog input will show a -20 indication on the meters (equivalent to 0 VU).
ON —
ON —
ON —
ON —
ON —
When pressed, turns the module on, lighting the button and routing the module audio to the
selected buses. Logic control commands (timer reset, start pulse, Cue reset, etc.), may be initiated,
depending upon the SETUP DIP switch settings.
OFF —
OFF —
OFF —
OFF —
OFF —
When pressed, turns the module off, removing the module audio from all selected buses (except
those that are set for pre-switch operation). Logic control commands (Stop Pulse, Off Tally, etc.) may be
initiated, depending upon the SETUP DIP switch settings.
Telco/Codec Module
