Commissioning
Leading the Furling Line to the Cockpit
08/05/09
Unit 00AL
41
1
The furling line is shipped with one end attached to
the furling drum. Charge the system by turning the
foils to wrap line on the drum.
2
Use the provided 5 mm allen wrench to loosen the two line guard screws. Align the basket so the furling line leads
properly at all times. The angle at which the line exits the basket changes as the amount of line on the spool chang-
es. Check for chafe with varying amounts of line on the spool before locking the unit.
4IP3UNCOVERTOSTARBOARDTURNCLOCKWISETOCHARGE3UNCOVERTOPORTTURNCOUNTERCLOCKWISE4ENSIONLINEWHILECHARGING
4IP4HEPOSITIONOFTHESUNCOVERONTHESAILDETERMINESTHEDIRECTION
OFROTATION3UNCOVERTOSTARBOARDhCHARGEvBYTURNINGCLOCKWISE
3UNCOVERTOPORThCHARGEvBYTURNINGCOUNTERCLEEP
TENSIONONTHELINEWHILEhCHARGINGv
.OTE
when replacing line, pass it through enclosed
opening in guard. Pass line into hole in hub of spool.
Pull line down from below and clamp on HCP237
“hog ring”. Pull back to tighten.
When replacing line, pass it through
enclosed opening in guard. Pass line into
hole in hub of spool. Pull line down from
below and clamp on a HCP237 “hog ring”.
Pull back to tighten.
Use the provided 5 mm allen wrench to loosen the two
line guard screws.
7402
RATCHET STANCHION BLOCK
POULIE WINCH DE
GUIDAGE À CLIQUET
CARBO RATSCH-BLOCK
MIT SÜTZEN-BASIS
BOZZELLO A CRICCO PER CANDELIERE
34%2.s!22)µ2%s(%#+s0/00!
"/7s
ÉTRAVE
s
BUG
s025!
7401
FORWARD STANCHION BLOCK
POULIE DE GUIDAGE POUR CHANDELIER
CARBO BLOCK MIT SÜTZEN-BASIS
BOZZELLO CANDELIERE DI PRUA
7403
OUTBOARD STANCHION BLOCK
POULIES DE GUIDAGE
EXTERNES
ÄUSSERE
REFFLEINEN-FÜHRUNG
BOZZELLI ESTERNI
DEI CANDELIERI
Note
: As furling line lead changes, make sure line
doesn’t chafe against line guard. Rotate line guard
if necessary.
Position 7401 Forward Stanchion Block so line
enters drum at right angles to headstay and centers
vertically in opening. Install so line is inside stanchion.
#ORRECTBLOCKPOSITIONISCRITICALTOEVEN
LINESPOOLINGANDEASEOFFURLING
7401 Forward Stanchion Block
Install 7403 Outboard Stanchion Blocks so line is
outside stanchions.
Number and placement of leads depends on boat
length and number/configuration of stanchions.
7403 Outboard Stanchion Blocks
Mount 7402 Ratchet Stanchion Block as furthest-aft
lead to prevent line overrides in drum when unfurling.
Position ratchet block so line turns at least 90°.
Install so line is inside stanchion.
Lead line through block so ratchet makes
clicking sound when pulling line to furl sail.
4IP-AKESURERATCHETSWITCHISINh/.vPOSITION
)FTHEREISNOCLICKINGSOUNDLEADLINETHROUGH
BLOCKINOPPOSITEDIRECTION
Lead line to Furling Line Cleat in cockpit.
7402 Ratchet Stanchion Block
Install so line is angled as shown.
Use #10 (5 mm) fasteners.
HCP168 Furling Line Cleat
2. Drum Empty
(sail furled)
1. Drum Full
(sail unfurled)
1. Tambour plein (voile déroulée)
1.
Trommel voll (Segel ausgerollt)
1.
Tamburo pieno (vela aperta)
2. Tambour vide (voile enroulée)
2.
Trommel leer (Segel eingerollt)
2.
Tamburo vuoto (vela chiusa)