Haefely 2830 User Manual Download Page 78 | Manualshive

Page: 78 / 124

Haefely 2830 User Manual Download Page 78

70

Software

Stop Test

This button state is used to stop the measurement, before the count down is
finished

.

The status labels of the DC Resistivity measuring unit have following meaning:

Set Power On

After starting up the 2830 software a power on command will be sent to the DC
Resistivity measuring unit. Before the first DC resistivity measurement will be
done it has to be started up.

Wait Power On

During power up phase.

Wait Calibrated

After powering up a calibration will be done.

Check Calibration

Validate the calibration.

Power On

The unit is started up.

Measure

During a measurement.

Set Stop

A stop command is sent to break the actual running measurement.

Wait Stopped

Wait until the stop command was executed.

Measure Cancelled

When a measurement was not done completely, “Measure Cancelled” will be
labelled.

9.5.1

Test cell shorting

As mentioned in the chapter 9.5 DC Resistivity the liquid test cell should be shorted before a DC

Resistivity measurement is done after a C Tan



measurement.

The shorting is also done in the DC Resistivity tab sheet but no voltage and measuring time has
to be set only the blue shorting time has to be set. During the shorting phase the “U” and “a” plug
on the front panel is shorted.

«
...
76
77
78
79
80
...
»

Summary of Contents for 2830





























































































































Reviews:

No comments