Haefely 2830 User Manual Download Page 74 | Manualshive

Page: 74 / 124

Haefely 2830 User Manual Download Page 74

66

Software

Save Raw Data

Store recorded raw data of the ADC. Filename can be selected. The
data are stored as CSV format (Comma Separated Values). Should
only be used for debugging purpose.

Save Log Data

Pressing this button will save the logged measurement values as
displayed in the scope at the left side.

9.5

DC Resistivity

The DC Resistivity mode is used to perform single measurements straight away. It displays all
necessary values at a glance and allows to capture a measurement by a single mouse click.
According the standard the liquid test cell should be shorted (see the following chapter 9.5.1 Test

cell shorting) before carry out the DC Resistivity measurement when a C Tan



measurement was

done before.

The following screen shot shows a running measurement on the heater 2903 #2 and liquid test
cell 2 as an example. Both heater are heating.

Depending on the made settings in the sub tab sheet (see chapter 9.3.3 Heating cell(s)) it is
displayed either one to two liquid heaters or one solid test cell in the heater & cells status section.

«
...
72
73
74
75
76
...
»

Summary of Contents for 2830





























































































































Reviews:

No comments