manualshive.com logo in svg

Haag-Streit VISUTRON 900 Touch, User Manual

Share
Download
Haag-Streit VISUTRON 900 Touch User Manual Download Page 81

Table 9

 – Guidance and Manufacturer’s Declaration

Electromagnetic Immunity

Immunity to Proximity Fields from RF Wireless Communications Equipment

Guidance and Manufacturer’s Declaration - Electronic Immunity

The Visutron 900 

Touch

 is intended for use in the electromagnetic environment as specified below 

related to proximity fields from RF wireless communications equipment.

Immunity 

Test

IEC 60601Test Level

Compliance  

Level

Electromagnetic  

Environment 

 

-Guidance-

Radiated RF 

IEC 61000-4-3

Test 

Frequency 

(MHz)

Band (MHz)

Service (MHz)

Modulation

Maximum 

Power (W)

Distance 

(m)

Immunity 

Test Level 

(V/m)

Compliance 

Level

RF wireless 

communications 

equipment should 

be no closer to any 

part of the Visutron 

900 

Touch

, including 

cables, than the 

recommended 

separation distance 

calculated from the 

equation applicable 

to the frequency of 

the transmitter.

Recommended 

Separation Distance:

d =  6/E √P

where

d = Minimum 

separation 

distance in 

meters

E = Immunity test 

level in V/m

P = Maximum 

power in Watts 

(W)

385

380-390

TETRA 400

Pulse Modulation 

18 Hz

1,8

0,3

27

27 V/m at 

0,3 m

450

430-470

GMR 460, FRS 

460

FM ±5 kHz 

deviation 1 kHs 

sine

2

0,3

28

28 V/m at 

0,3 m

710

704-787

LTE Band 13, 17 Pulse Modulation 

217 Hz

0,2

0,3

9

9 V/m at 0,3 m

745

780

810

800-960

GSM 800/900, 

TETRA 800, 

iDEN 820, CDMA 

850, LTE Band 1, 

3, 4, 25; UMTS

Pulse Modulation 

18 Hz

2

0,3

28

28 V/m at 

0,3 m

870

930

1720

1700-1990

GSM 1800; 

CDMA 1900; 

GSM 1900; 

DECT; LTE Band 

1, 3, 4, 25; UMTS

Pulse Modulation 

217 Hz

2

0,3

28

28 V/m at 

0,3 m

1845

1970

2450

2400-2570

Bluetooth WLAN, 

802.11 b/g/n, 

RFID 2450, LTE 

Band 7

Pulse Modulation 

217 Hz

2

0,3

28

28 V/m at 

0,3 m

5240

5100-5800 WLAN 802.11 a/n Pulse Modulation 

217 Hz

0,2

0,3

9

9 V/m at 0,3 m

5500

5785

Guidance Tables 

(continued)   

81

16243-101 Rev. G

Summary of Contents for VISUTRON 900 Touch

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands