Grunbeck GENO-OSMO-X Operation Manual Download Page 65

Page: 65 / 76

Reverse osmosis system

GENO-OSMO-X

Order no.

134 750 927-inter Edited by: phar/mrie G:\BA-750927-inter_134_GENO-OSMO_X.docx

Continuation table G-1: Warnings

This is what you observe

This is the cause

This is what to do

W037
Stop filter sys. or overfill safety
BB1

Tank has reached max. filling
level.

Check filling level in tank and regu-
late, if necessary.

W038
Comm. error MK200 12RA

Bus connection to MK200 12RA
module disturbed.

Check bus cabling and restore, if
necessary.

W039
Error KK200 12RA defective

MK200 12RA module disturbed.

Check setting at the module, check
parametrisation.

W040
Comm. error MK200 4AA

Bus connection to MK200 4AA
module disturbed.

Check bus cabling and restore, if
necessary.

W041
Error MK200 4AA defective

MK200 4AA module disturbed.

Check setting at the module, check
parametrisation.

W053
Communication error
basic circuit board

Faulty connection between touch
panel GENO-tronic and basic cir-
cuit board.

Notify Grünbeck’s technical cus-
tomer service/authorised service
company.

W055
Firmware basic circuit board out
of date

Firmware basic circuit board out
of date

Software version of operating ele-
ment does not match with the basic
circuit board

W056
SD card removed

SD card missing, defective.

Insert/replace SD card.

W057
SD card full

Memory of SD card full.

Replace SD card.

W058
SD card E/A error

SD card defective.

Replace SD card.

W060
EH (water softener) lack of salt

Not enough salt in brine tank.

Check salt level in brine tank and re-
fill salt tablets as per DIN EN 973 A,
if necessary.

W061
EH (water softener) service in-
terval

Maintenance interval of water sof-
tener has expired.

Notify Grünbeck’s technical cus-
tomer service/authorised service
company.

W062
DEA (pressure booster system)
service interval

Maintenance interval of pressure
booster system has expired.

Notify Grünbeck’s technical cus-
tomer service/authorised service
company.

W063
DEA ext. release signal lacking

Release signal selected incor-
rectly.

Check parameter settings.

W064
DEA dry-run protection

Not enough water in the supply
tank.

Signal acknowledges itself as soon
as sufficient water is available again.

W065
DEA power failure

Power failure >1 minute.

Check parameter setting in operator
menu. Ensure power supply.

Summary of Contents for GENO-OSMO-X













































































Search results

Summary of Contents for GENO-OSMO-X

Reviews:

Related manuals for GENO-OSMO-X

Brands by name

Popular brands

Grunbeck GENO-OSMO-X, Operation Manual

Search results

Summary of Contents for GENO-OSMO-X

Reviews:

Related manuals for GENO-OSMO-X

Brands by name

Popular brands