manualshive.com logo in svg

Grunbeck GENO-OSMO-X, Operation Manual, Page: 69 / 76

Share
Download
Grunbeck GENO-OSMO-X Operation Manual Download Page 69

 

Reverse osmosis system 

GENO-OSMO-X 

 

 

 

 

 

Order no.

 

134 750 927-inter   Edited by: phar/mrie  G:\BA-750927-inter_134_GENO-OSMO_X.docx 

67

Continuation table G-2: Troubleshooting 

This is what you observe  This is the cause 

This is what to do 

E120: 
Error micro-switch 

Outside of the regeneration, 
the signal of micro-switch S2 
is pending at terminal 14. 

Check wiring and function of the 
switch and notify Grünbeck’s 
technical customer service/au-
thorised service company, if 
necessary. 

E124: 
Error motor current 

Monitoring of the step motor 
current has reacted. 

If the error occurs again within 5 
minutes after it was acknowl-
edged, notify Grünbeck’s tech-
nical customer service/ author-
ised service company. 

E127: 
Bus error RO1 - DEA1 

Communication with data line 
RS485 to control unit of the 
pressure booster installed 
downstream is interrupted. 

Check the lines for proper con-
nection. Check whether the ter-
minating resistors (DIP 
switches) are set properly. 

E150: 
Stage 2 Error OSMO-X 

Control unit defective. 

Notify Grünbeck’s technical cus-
tomer service/authorised service 
company. 

E151: 
Stage 2 Error power fail-
ure 

Power failure has occurred, 
system is not set to automatic 
restart. 
Whether this affects other 
subsystems as well, has to be 
checked on site. 

Ensure reliable power supply of 
GENO-OSMO-X  
Refer to chapter F-4.1: 
If necessary, reprogram the pa-
rameter "automatic system re-
start". 
 

E152: 
Stage 2 EEPROM 

EEPROM defective. 

Notify Grünbeck’s technical cus-
tomer service/authorised service 
company. 

E153: 
Stage 2 Comm. error 
stage 1   

Communication with data line  
RS485 to control unit installed 
upstream/downstream is in-
terrupted. 

Check the lines for proper con-
nection. Check whether the ter-
minating resistors (DIP 
switches) are set properly. 

E154: 
Comm. error stage 2 
E155 
Stage 2 sensor error pres-
sure 

Malfunction at the sensor sig-
nal 4-20 mA of the pressure 
sensor. 

Notify Grünbeck’s technical cus-
tomer service/authorised service 
company. 

E156 
Stage 2 sensor error level 
probe 

Malfunction at the sensor sig-
nal 4-20 mA of the permeate 
tank’s level probe. 

Notify Grünbeck’s technical cus-
tomer service/authorised service 
company. 

E157 
Stage 2 sensor error 
RO1CQ2 

Malfunction at the sensor sig-
nal LF/PT100 of the conduc-
tivity probe. 

Notify Grünbeck’s technical cus-
tomer service/authorised service 
company. 

Summary of Contents for GENO-OSMO-X













































































Reviews:

No comments