GRAUPNER 32032, Programming Manual

Page: 109 / 324

109 Detail program description - Control adjust | Winged models
"GL": The settings for the input in question affect
all fl ight phases programmed (if any) and
thus act "globally" on the model memory in
question.
"PH": The settings for this input take effect per
fl ight phase and must therefore be confi gured
separately for each fl ight phase.
Note:
See page 140 for more information about fl ight
phases.
Column 3, "Transmitter control/switch
assignment"
Select an input, 5 through 16, with the
cd
selection
keys of the left or right touch pad.
Transmitter control assignment
Use the selection keys to move into the column
labeled
SEL . After completing the activation of
transmitter control assignment by tapping the center
SET key of the right touch pad , the message shown
below will appear in the display:
0% +100% I5
I6
I7
I8
TYP SEL
+100% 0.0 0.0
– –time+
0% +100% +100% 0.0 0.0
0% +100% +100% 0.0 0.0
0% +100% +100% 0.0 0.0
GL
GL
GL
fr ---
fr
fr
fr
---
---
---
Offset
GL
Nor mal
Move desired
control adj.
Now actuate the desired transmitter control: The
notice window will disappear and the designation
of the selected transmitter control will appear in the
transmitter control assignment window.
0% +100% I5
I6
I7
EI
TYP SEL
+100% 0.0 0.0
– –time+
0%
+100% +100% 0.0 0.0
0% +100% +100% 0.0 0.0
0% +100% +100% 0.0 0.0
GL
GL
GL
S11 ---
fr
fr
fr
---
---
---
Offset
GL
Nor mal
Alternatively, the center SET key of the right touch
pad can be tapped for a second time while the notice
window, see above, is still on the display:
0% +100% I5
I6
I7
EI
TYP SEL
+100% 0.0 0.0
– –time+
0% +100% +100% 0.0 0.0
0% +100% +100% 0.0 0.0
0% +100% +100% 0.0 0.0
GL
GL
GL
fr ---
fr
fr
fr
---
---
---
Offset
GL
Nor mal
Now use the selection keys of the left or right touch pad
to select the desired input out of the list if the respective
plug-in location on the transmitter board is occupied or
switch the entry to "fr" if the input is to be decoupled
from a transmitter control. In this case, or even when a
non-existent transmitter control is assigned, the servo
corresponding to this input will be in its neutral position
and can only be controlled via mixers.
0% +100% I5
I6
I7
EI
TYP SEL
+100% 0.0 0.0
– –time+
0% +100% +100% 0.0 0.0
0% +100% +100% 0.0 0.0
0% +100% +100% 0.0 0.0
GL
GL
GL
S11 ---
fr
fr
fr
---
---
---
Offset
GL
Nor mal
Switch assignment
If the input is to be actuated like a switch module, the
input can alternatively be assigned to a switch.
A simple switch can be used to switch back and forth
between two limit values, for example motor On/Off.
A 2-way momentary or toggle switch, see appendix,
achieves the same effect as a 2-channel switch
module, for example motor Off/Half/Full.
Use the selection keys to move into the column
above the
switch symbol label. Briefl y tap the
center SET key of the right touch pad to activate the
option for assigning a switch.
0% +100% I5
I6
I7
I8
TYP SEL
+100% 0.0 0.0
– –time+
0% +100% +100% 0.0 0.0
0% +100% +100% 0.0 0.0
0% +100% +100% 0.0 0.0
GL
GL
GL
---
fr
fr
fr
---
---
---
Offset
GL fr
Nor mal
Move desired switch
to ON position
(ext. switch: ENTER)
Actuate the desired toggle switch from its "OFF"
to its "ON" position or, for a 3-way switch,
beginning from its middle position , assign a switch
direction – preferably the "second" direction. This
means, if a function is to be switched on by moving
the switch forward two positions, i.e. away from the
pilot, then begin from the switch's middle position and
move the switch away from the pilot.
The display will then present the switch number
together with a symbol indicating the given switch
direction. At the same time, the column label in the
footer line will change from
SEL into another switch
symbol.