manualshive.com logo in svg

Graco LineLazer V 200MMA, Operation - Repair - Parts

Share
Download
Graco LineLazer V 200MMA Operation - Repair - Parts Download Page 48

Maintenance - Fusion MMA PC Gun 

48

3A9099A Operation, Repair, Parts

Inspect the Check Valves

1. Follow the 

Pressure Relief Procedure

, page 14. 

2. Follow 

Flush Gun

, page 47, to remove residual 

chemical. 

3. Remove the Gun Fluid Manifold (12), see 

Clean 

Passages

, page 54. Leave air connected. 

Clean 

Gun Fluid Manifold

, page 53.

4. Shut off air.

5. Pry out check valves (26) at notch.

6. Slide filter (26d) off. Clean and inspect parts. 

Thoroughly inspect o-rings (26f, 26g). If necessary, 

remove screw (26b) and disassemble entire check 

valve.

7. Reassemble check valves. Screw (26b) should be 

flush (within 1/16 in. or 1.5 mm) of housing (26a) 

surface. Liberally lubricate o-rings (26f, 26g) and 

carefully reinstall in fluid housing.

8. Attach the Gun Fluid Manifold, see 

Clean 

Passages

, page 54. Connect air. Return gun to 

service.

NOTICE

To prevent cross-contamination in the gun, do not 

interchange A component and B component parts. 

Cross-contamination can result in cured material in the 

gun. Cured material may damage the sealing surfaces, 

block fluid passages, and prevent gun function.

12

Damaged check o-rings (26f, 26g) may result in 

external leakage. To avoid potential leakage and 

serious injury from skin injection, replace any 

damaged o-rings.

Summary of Contents for LineLazer V 200MMA



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands