manualshive.com logo in svg

Graco LineLazer V 200MMA, Operation - Repair - Parts

Share
Download
Graco LineLazer V 200MMA Operation - Repair - Parts Download Page 63

Troubleshooting

3A9099A Operation, Repair, Parts

63

Spray icon is always shown 

on display.

Interrupter is improperly positioned.

Turn screw clockwise until spray icon is 

synchronized with fluid spray, page 25.

Reed switch assembly is damaged.

Replace reed switch assembly.

Pumps are running at largely 

different speeds

Fluid filter is dirty.

Clean filter.

Tip, Filter or Manifold is clogged.

Clean components, drill passages.

Displacement pump is stuck.

Repair pump, see pump manual.

Impingement ports clogged.

Clean, see 

Clean Mix Chamber 

Impingement Ports

, page 49.

AUTO GUN MODE

Auto Gun won’t actuate 

when the red button is 

pressed.

Gun is not activated.

Press the 1 or 2 button on control to activate 

a gun.

Cable is not adjusted properly.

Adjust Cable to properly actuate gun trigger, 

page 26.

Not on main striping screen.

Go to main striping screen on control to 

Actuate Auto Guns.

Low Speed Shut off is enabled.

Disable Low Speed Shutoff, page 42.

Battery Voltage is too low.

Check Battery voltage on Diagnostic Screen, 

page 15, or with Volt meter. If below 11.5V, 

charge Battery or replace Battery.

Cable is not adjusted properly.

Adjust Cable to properly actuate gun trigger, 

page 26.

Red button is broken.

Test button functionality in Diagnostic screen, 

page 15. Replace if broken.

Auto Gun Cable is broken or extremely 

kinked resulting in too much drag.

Replace Auto Gun Cable.

Solenoid wire is disconnected or broken.

Check Wiring Diagram, page 92, repair or 

replace wires if necessary.

Fuse to Battery is removed or blown.

Check and replace fuse.

Solenoid is jammed.

Spray Lubrication on solenoid plunger.

Solenoid is failed.

Check resistance across solenoid wires. 

Resistance should be between .2 and .26 

ohms. If it’s not, replace solenoid.

Control board is failed.

Replace Control board.

Gun is not receiving air.

Check air pressure. Open air valve on gun.

Air pressure too low.

Increase motor speed, check air connections 

& spray tip adapter.

Line Spacing is not accurate Wrong line pattern loaded.

Reload the correct pattern.

Machine is out of calibration.

Calibrate the machine, page 21.

Problem

Cause

Solution

Summary of Contents for LineLazer V 200MMA



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands