manualshive.com logo in svg

Graco LineLazer V 200MMA, Operation - Repair - Parts

Share
Download
Graco LineLazer V 200MMA Operation - Repair - Parts Download Page 57

Maintenance - LineLazer V 200MMA 1:1

3A9099A Operation, Repair, Parts

57

Maintenance - LineLazer V 200MMA 1:1

Periodic Maintenance

DAILY: 

After every use, thoroughly clean gun and 

components with acetone.

DAILY: 

Check air lines for clear passage ways. Ensure 

paint is not backed into air hose/fittings.

DAILY: 

Check engine oil level and fill as necessary.

DAILY: 

Check hydraulic oil level and fill as necessary.

DAILY: 

Check hose for wear and damage.

DAILY: 

Check gun safety for proper operation.

DAILY: 

Check prime/spray drain valve for proper 

operation.

DAILY: 

Check and fill gas tank

DAILY: 

Check that displacement pump is tight.

DAILY: 

Top off TSL level in displacement pump 

packing nut to help prevent material buildup on piston 

rod and early wear of packing.

AFTER THE FIRST 20 HOURS OF OPERATION: 

Drain 

engine oil and refill with clean oil. Reference Honda 

Engines Owner’s Manual for correct oil viscosity.

WEEKLY: 

Remove engine air filter cover and clean 

element. Replace if necessary. If operating in an 

unusually dusty environment, check filter daily.

WEEKLY/DAILY: 

Remove any debris from hydraulic 

rod.

AFTER EACH 100 HOURS OF OPERATION: 

Change 

engine oil. Reference Honda Engines Owner’s Manual 

for correct oil viscosity. 

SEMI-ANNUALLY: 

Check belt wear, replace if 

necessary.

YEARLY OR 2000 HOURS: 

Replace belt.

AFTER EACH 500 HOURS OR 3 MONTHS OF 

OPERATION: 

Replace hydraulic oil and filter. Use 

Graco hydraulic oil 169236 (5 gallon/20 liter) or 207428 

(1 gallon/3.8 liter) and filter 246173. Oil change interval 

dependent on environmental conditions.

SPARK PLUG: 

Use only BPR6ES (NGK) or W20EPR--U 

(NIPPONDENSO) plug. Gap plug to 0.028 to 0.031 in 

(0.7 to 0.8 mm). Use spark plug wrench when installing 

and removing plug.

Caster Wheel

1. Once each year, tighten nut under dust cap until 

spring washer bottoms out, then back off the nut 

1/2 to 3/4 turn.

2. Once each month, grease the wheel bearing.

3. Check pin for wear. If pin is worn out, there will be 

play in the caster wheel. Reverse or replace the pin 

as needed.

4. Check caster wheel alignment as necessary. To 

Summary of Contents for LineLazer V 200MMA



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands