manualshive.com logo in svg

Graco LineLazer V 200MMA, Operation - Repair - Parts

Share
Download
Graco LineLazer V 200MMA Operation - Repair - Parts Download Page 67

Gun Troubleshooting

3A9099A Operation, Repair, Parts

67

Problem

Cause

Solution

Excessive cleanoff air when 

fluid valves are closed and 

gun is triggered.

The fluid cartridge front o-ring is damaged or 

missing.

Replace the fluid cartridge front o-ring only. 

See 

Parts Drawing - Gun

, page 74.

Fluid does not shut off when 

fluid valves are closed.

The fluid valves are damaged.

Replace the fluid valves. See 

Parts Drawing - 

Gun

, page 74.

Burst of air from muffler when 

gun is triggered.

Normal.

No action required.

Steady air leakage from 

muffler.

The air valve o-rings are damaged.

Replace the valve o-rings. See 

Inspect the Air 

Valve

, page 55.

The piston o-rings are damaged.

Replace the piston o-rings. See 

Parts 

Drawing - Gun

, page 74.

Air leakage from front air 

valve.

The air valve o-rings are damaged.

Replace the valve o-rings. See 

Inspect the Air 

Valve

, page 55.

Air leak around lock ring.

The o-ring is damaged.

Replace the o-ring. See 

Parts Drawing - Gun

, 

page 74.

Cannot tighten retaining ring 

(9) until it bottoms out.

The spray tip adapter was assembled before 

retaining ring.

Install retaining ring (9) first, then spray tip 

adapter (10). See 

Assemble the Spray Gun

, 

page 15.

Excessive air leaking from 

sides of gun.

The retaining ring is loose.

Tighten retaining ring.

The o-ring is missing on back of cartridge.

Replace o-rings. See 

Parts Drawing - Gun

, 

page 74.

The rear cartridge OD o-ring is damaged or 

missing.

Replace o-ring. See 

Parts Drawing - Gun

, 

page 74.

Fluid or chemical is leaking 

from sides of gun.

The fluid o-ring are damaged or missing.

Replace o-ring. See 

Parts Drawing - Gun

, 

page 74.

Summary of Contents for LineLazer V 200MMA



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands