Graco LineLazer V 200MMA Operation - Repair - Parts Download Page 54

Page: 54 / 98

Maintenance - Fusion MMA PC Gun

3A9099A Operation, Repair, Parts

Clean Passages

1. Perform

Pressure Relief Procedure

, page 14.

2. If necessary, clean out passages in fluid housing

and handle with drill bits. Refer to

ABLE

1 and to

. 1

for diameter and location of passages.

Clean Muffler

Remove and clean Muffler with acetone.

Inspect the Piston

1. Perform

Pressure Relief Procedure

, page 14.

2. Disconnect air lines (D) from Air Line Quick Coupler

(4) and remove Gun Fluid Manifold (12).

Disassemble Front End of Fusion MMA PC Gun

page 56.

4. Unscrew cylinder cap (5) and inspect o-ring (14).

Reference

Parts Drawing - Gun

, page 74.

5. Push piston shaft to remove piston (15). Inspect

piston o-ring (16) and shaft o-ring (17). Reference

Parts Drawing - Gun

, page 74.

Table 1: Passage Diameters

Passage Description

Ref. Letter Diameter

in. (mm)

Optional Air Inlet

7/16, 1/8 (11.0, 3.1)

Purge Air

1/8 (3.1)

Piston Air

ZD, ZE

1/8 (3.1)

Air Exhaust

11/32, 1/8 (8.7, 3.1)

Air Valve Bore

9/32 (7.1)

Cleanoff Air

3/32 (2.35)

Grease

3/32 (2.35)

Fluid Housing Purge Air

5/32 (3.97)

. 1

Gun Handle Passages

. 2 Fluid Housing Passages

ZD ZE

WLD

TI2430A

TI2431A

Summary of Contents for LineLazer V 200MMA



































































































Search results

Summary of Contents for LineLazer V 200MMA

Reviews:

Brands by name

Popular brands

Graco LineLazer V 200MMA, Operation - Repair - Parts

Search results

Summary of Contents for LineLazer V 200MMA

Reviews:

Brands by name

Popular brands