Graco LineLazer V 200MMA Operation - Repair - Parts Download

Page: 14 / 98

Pressure Relief Procedure

3A9099A Operation, Repair, Parts

Pressure Relief Procedure

1. Perform

Grounding Instructions

, page 13.

2. Set both Pump ON/OFF Valves to

OFF

3. Turn Pressure Control to lowest setting.

4. Close Fluid Valves A and B on the Gun Fluid

Manifold with the provided 5/16” nut driver.

5. Trigger the gun onto cardboard or into a waste

container to relieve pressure.

6. Engage all gun Piston Safety Locks. Turn both

Prime Valves to prime positions.

Clear Spray Tip Adapter Clog

7. If you suspect the Spray Tip Adapter (3) is clogged

or that pressure has not been fully relieved:

a. Repeat

Pressure Relief Procedure

steps 1-6.

b. Remove the Spray Tip Adapter VERY SLOWLY.

c. Clear the obstruction in the Spray Tip Adapter

(3) and reinstall.

Clear Spray Tip Clogs

1. Release trigger. Engage Piston Safety Lock. Rotate

Spray Tip (22). Disengage Piston Safety Lock and

trigger gun to clear the clog.

2. Engage Piston Safety Lock, return Spray Tip (22) to

original position, disengage Piston Safety Lock and

continue spraying.

This equipment stays pressurized until pressure is

manually relieved. To help prevent serious injury from

pressurized fluid, such as skin injection, splashing

fluid and moving parts, follow the Pressure Relief

Procedure when you stop dispensing and before

cleaning, checking, or servicing the equipment.

Summary of Contents for LineLazer V 200MMA



































































































Search results

Summary of Contents for LineLazer V 200MMA

Reviews:

Related manuals for LineLazer V 200MMA

Brands by name

Popular brands

Graco LineLazer V 200MMA, Operation - Repair - Parts

Search results

Summary of Contents for LineLazer V 200MMA

Reviews:

Related manuals for LineLazer V 200MMA

Brands by name

Popular brands