manualshive.com logo in svg

GILBARCO VEEDER-ROOT Encore 700 S, Start-Up And Service Manual

Share
Download
GILBARCO VEEDER-ROOT Encore 700 S Start-Up And Service Manual Download Page 49

DCM2.2

Service

MDE-4902E Encore® 700 S Start-up and Service Manual · February 2018

Page 4-19

DCM2.2 

DCM2.2 (M15737A001) Highlights

Figure 4-15: DCM2.2 Board

JP6 - New Jumper for Pump 
Current Loop Selection

JP5 - New Jumper for VLAN 
(UX410)

New - These ports become dedicated for specific devices 
when VLAN Jumper is installed (printed on the PCB)

 P333 - New Connector for 
Dedicated High-Speed 

JP12 - New SmartCRIND 
Jumper

J3 HomePlug 
New Location

DCM2.2 LED Functions

The following table lists the LED functions of DCM2.2:

LED Functions

D1 Power Good 

VDC 24V is “ON” = Good

D23 HP UP

HomePlug jumper is installed “ON” = Good, CPU is running, but does not indicate 
that there is a connection to the BRCM2.X in back room. Internal CCP status only.

D20 SSoM REG

Registered to the cloud

D19 SSoM USB

USB port activity LED

D13 ETH LINK ACT

Same as DCM2.1 - HomePlug jumper is OFF, P304 direct ethernet connection active

D18 HomePlug

HomePlug is active and connected to BRCM2 (2.1 or 2.2)

D21 LED “Router Enable” If “ON Green”, SSoM is installed and running, does not mean it is configured 

properly. If LED is “OFF”, the assembly must be replaced.

D5 and D6

New labeling - NON-OLC, monitors P300 pins 1 and 3

D4 and D7

OLC (new labeling), monitors either P300 pins 4 and 5 or P333 pins 3 and 4 
depending on the two-wire configuration 

D2

Reversed two-wire

D14

Reversed two-wire

Summary of Contents for Encore 700 S









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands