GILBARCO VEEDER-ROOT Encore 700 S Start-Up And Service Manual Download Page 13

Page: 13 / 72

MDE-4902E Encore® 700 S Start-up and Service Manual · February 2018

Page 3-1

Configuring CRIND

Start-up

3 – Start-up

Configuring CRIND

The CRIND device on each side is programmed individually by inserting the CRIND
Diagnostic Card (Q12534-170) on each side (cannot be done from the same side). In CRIND
diagnostics, you must press

Enter

after each numeric key entry on the FlexPay EPP.



“Side 1” appears irrespective of the side being programmed.

Due to enhanced security of the FlexPay UPT, you must press

Enter

after each key entry

when using CRIND diagnostics.

IMPORTANT INFORMATION

Note: For more information on Encore 700 S Electronics CRIND Basic Input/Output System

(BIOS), refer to MDE-4185 CRIND Encore 700 S Electronics CRIND BIOS
Configuration Interface Manual.

To access CRIND diagnostic programming, proceed as follows:

Insert and remove the CRIND diagnostic card.

Note: Card reader is sensitive to light and may not be able to read the card if the door is open.

Close the main doors to eliminate any outside light intrusion.

Figure 3-1: Swiping CRIND Diagnostic Card

CRIND Diagnostic Card (Q12534-170)

Summary of Contents for Encore 700 S









































































Search results

Summary of Contents for Encore 700 S

Reviews:

Related manuals for Encore 700 S

Brands by name

Popular brands

GILBARCO VEEDER-ROOT Encore 700 S, Start-Up And Service Manual

Search results

Summary of Contents for Encore 700 S

Reviews:

Related manuals for Encore 700 S

Brands by name

Popular brands