background image

UFO-NT

42

Commissioning and service

20  Commissioning and service

Commissioning and service can be performed using the DPS DPS, the service terminal ST220 or the internal 

service keys.

20.1  Commissioning

20.1.1  Requirements

 

à

Drive

 

à

attached 

 

à

not taught 

 

à

set to default setting

 

à

Electrical installation is complete. 

 

à

During commissioning the DPS displays “LE”.

 

à

When newly teaching the drive: both drives to automatic operating mode.

20.1.2  Carrying out commissioning

 

X

Check whether the drive works mechanically when de-energised (check by hand). 

 

X

Switch the mains switch on.

 

X

Set the peripheral equipment before the teaching run. 

 

X

Perform the teaching run as described in chapter 20.2 "Teaching run". 

The safety sensor is active due to teaching wall blanking. 

 

X

Check the functionality of the safety sensors.

 

X

Check other functions.

 

X

The set static and dynamic forces must be measured

Optional: 

The braking force in the disconnected state can be set for different door weights. See chapter 21, "Disconnected 

mode".

20.2  Teaching run

 

à

For the teaching run to be carried out, the drive must be completely installed and supplied with voltage.

 

à

The spring force required must be set before the teaching run, see Powerturn installation instructions.

 

X

Mechanically set on drive and calibrate on the door leaf.

 

à

If “Start teaching” is started using the parameter menu (DPS, ST220, service keys), the user has 1 minute to 

start the teaching process.

 

à

If the door is not moved within this time, the drive cancels the teaching run and retains the data previously 

stored.

 

à

In the default setting the safety sensors are configured as active.

 

à

The teaching run starts and ends in the closed position so that the drive learns the direction of opening/clos-

ing movement properly. 

The following points must be observed:

 

à

Activating the safety sensor within the movement run (part of the teaching process) does not stop the door 

leaf. For this reason, only complete  a movement run under supervision or with passage safeguard.

 

à

If the door leaf is blocked within the movement run, fault message 25 is issued and the teaching run must be 

repeated.

If a 2-leaf system has to be taught, the “Number of leaves” (EF) parameter must first be installed on both drives:

 

X

Select the parameter with service terminal ST220 or the DPS DPS and set the value 02 for active leaf and the 

value 03 for passive leaf. 

 

X

Connect both drives.

The drive differentiates between two conditions:

 

à

The drive is situated in the factory setting (factory setting) 

 untaught

 

à

Drive is re-taught

Summary of Contents for UFO-NT F

















































































Reviews: