There is an arrow sticker in the bottom
right side of the cover, which is
pointing to the shaft. Align the new
transfer unit with the shaft (
햲
), and
then slide the unit in place (
햳
).
AQV227S
While pressing down on the corner of the
transfer unit indicated by the arrow (
햲
),
return the green lever (
햳
) to its original
position to lock the transfer unit in place.
AQV228S
•
If you cannot return the green lever to its original
position, raise the green lever and remove the transfer
unit. After that, try to install the transfer unit again.
Leave the right cover open for replacing the develop-
ment unit.
Removing the Development
Unit from the Box
•
When taking the development unit out of the box, be
sure to hold the unit by the handle on the top of the
unit. Do not touch the side of the development unit.
Before taking the development unit out
of the box, open the center of the plastic
bag. Lift the green handle on the top of
the development unit. Be sure to use the
handle on the top of the unit.
AQV205S
Open the right cover by pushing the
catch upwards.
AQV224S
Put on the gloves included in the box.
Be sure to wear the gloves to avoid getting your hands
dirty or damaging the belt surface of the new transfer
unit.
TAPM310E
Raise the green lever (
햲
) inside the right
cover to release the transfer unit.
AQV226S
Hold both sides of the unit. Lift the side
of the unit closest to you slightly (
햲
),
and remove the unit from the printer
(
햳
) as shown. Put the used transfer
unit in the disposal bag.
AQV210S
•
After removing the transfer unit, put the unit in the
disposal bag. Be careful not to tilt or shake the unit.
Otherwise, toner might scatter.
Take the new transfer unit out of the box,
and remove the plastic bag.
Take the desiccant out.
Maintenance Kit SP 8100A
REPLACEMENT GUIDE
The maintenance kit contains the parts required to maintain the printer. When “Replace Maintenance Kit”
appears on the panel display, replace the parts included in the maintenance kit. Read this guide carefully
before you use the maintenance kit. For safety purposes, carefully follow the instructions in this guide.
Checking the Contents of
the Box
Maintenance Kit SP 8100A. Each box contains the
following parts. Confirm that the contents of the boxes
match the following lists.
Maintenance Kit SP 8100A
Replacement Guide (this sheet)
Development Unit
AQV206S
Disposal Bag
For packing the used Development Unit
Fusing Unit
AQV200S
Transfer Unit
AQV232S
Caution
•
The inside of the machine becomes very hot. Do not
touch the parts with a label indicating a “hot surface”.
Touching a “hot surface” could result in a burn injury.
•
Disposal should take place at an authorized dealer
or appropriate collection site.
•
If you dispose of the used parts yourself, dispose of
them according to local regulations.
Turning Off the Printer
Turn the printer’s power switch off.
•
The inside of the machine becomes very hot. Be sure
to turn off the printer before attempting to replace
any of the parts. When replacing the old fusing unit
with a new one, turn off the printer and wait for about
30 minutes before beginning the installation.
AQV311S
Hold the handle and lift the still
wrapped development unit with its
styrofoam packing out of the box.
AQV207S
While holding the handle, remove the
styrofoam packing from both ends of
the unit.
AQV209S
Lift the unit out of the plastic bag.
•
Replace the development unit. See “Replacing the
Development Unit”.
Replacing the
Development Unit
Warning
•
Do not incinerate the used development unit. Toner
dust might ignite when exposed to an open flame.
•
Disposal should take place at an authorized dealer
or appropriate collection site.
•
If you dispose of the used parts yourself, dispose of
them according to local regulations.
Open the front cover.
AQV201S
Open the bypass tray (
햲
), and then open
the duplex unit by pushing the catch
upwards (
햳
).
AQV223S
Open the right cover by pushing the
catch upwards.
AQV224S
While raising the green lever inside the
front cover (
햲
), and then slide the de-
velopment unit out about 10cm (4”).
AQV212S
Gloves
TAPM241E
Disposal Bag
For packing the used Transfer Unit
Brief reference sheet
If one or more of the items are missing, contact your
sales or service representative.
You should replace all the parts included in the
maintenance kit at the same time. Be sure to replace
them in the following order:
AQV203S
1. Transfer Unit
2. Development Unit
3. Fusing Unit
Replacing the
Transfer Unit
Warning
•
Do not incinerate the used transfer unit. Toner dust
might ignite when exposed to an open flame.
•
Disposal should take place at an authorized dealer
or appropriate collection site.
•
If you dispose of the used parts yourself, dispose of
them according to local regulations.
Open the bypass tray (
햲
), and then open
the duplex unit by pushing the catch
upwards (
햳
).
AQV223S
/ &!&$
AdonisP4Mainte_p65
06.1.30, 10:52 AM
1
Summary of Contents for P7245
