GE P741, Technical Manual

Page: 261 / 560

Programmable Logic P74x/EN PL/Na7
MiCOM P741, P742, P743 (PL) 7-
27
PL
Relay
DDB
No.
English Text Type Source Description
P742 346 CB Trip 3 ph PSL Input Signal 50BF Protection Triphase Circuit Breaker Trip from CU (Init
50BF TBF1 / TBF2), Logical OR of :
87BB, 50BF, Manual Trip Zone X
P742 347 CB Trip phase A PSL Input Signal 50BF Protection Phase A Circuit Breaker Trip (Init 50BF TBF3 /
TBF4), Logical OR of :
O/C Protection, External Trip A, External Trip
3ph
P742 348 CB Trip phase B PSL Input Signal 50BF Protection Phase B Circuit Breaker Trip (Init 50BF TBF3 /
TBF4), Logical OR of :
O/C Protection, External Trip B, External Trip
3ph
P742 349 CB Trip phase C PSL Input Signal 50BF Protection Phase C Circuit Breaker Trip (Init 50BF TBF3 /
TBF4), Logical OR of :
O/C Protection, External Trip C, External Trip
3ph
P742 351 General Alarm PSL Input Signal Relay Integrity General Alarm
P742 352 CB Status Alarm PSL Input Signal Scheme Integrity Indication of discrepancy between the 52a and
52b auxiliary contacts of the Circuit Breaker
P742 353 Man CB Cls Fail PSL Input Signal Scheme Integrity Circuit Breaker Failed to Close
(after a manual/operator close command)
P742 354 Man CB Trip Fail PSL Input Signal Scheme Integrity Circuit Breaker Failed to Trip
(after a manual/operator trip command)
P742 355 Ctrl Cls in Prog PSL Input Signal Commissioning Control Close in Progress
The relay has been given an instruction to close
the circuit breaker, but the Manual Close timer
Delay has not yet finished timing out
P742 356 Control Close PSL Input Signal Commissioning Control Close command to the circuit breaker.
Operates for a manual close command (menu,
SCADA)
P742 357 Control Trip PSL Input Signal Commissioning Control Trip
Operator trip instruction to the circuit breaker,
via menu, or SCADA. (Does not operate for
protection element trips)
P742 358 Any Trip PSL Input Signal All Protections Any Trip (Logical OR of ddbs:
0, 1, 2, 168, 169, 170, 171, 256, 261)
P742 362 RP1 Read Only PSL Output
signal PSL All setting changes and most command/control
actions blocked for Rear Port 1.
P742 363 RP2 Read Only PSL Output
signal PSL All setting changes and most command/control
actions blocked for Rear Port 2 (not used).
P742 376 87BB Fault Ph A PSL Output
signal PSL 87BB Phase Fault detected in phase A
P742 377 87BB Fault Ph B PSL Output
signal PSL 87BB Phase Fault detected in phase B
P742 378 87BB Fault Ph C PSL Output
signal PSL 87BB Phase Fault detected in phase C
P742 379 87BB Earth Fault PSL Output
signal PSL 87BB earth Fault detected
P742 428 LED Cond IN 1 LED_CON PSL Assignment of signal to drive LED 1 Red.
P742 435 LED Cond IN 8 LED_CON PSL Assignment of signal to drive LED 8 Red.
P742 436 Timer in 436 TIMERIN PSL Timer Input Input to Auxiliary Timer 1
P742 451 Timer in 451 TIMERIN PSL Timer Input Input to Auxiliary Timer 16
P742 452 Timer out 452 TIMEROUT Timer Output Output from Auxiliary Timer 1
P742 467 Timer out 467 TIMEROUT Timer Output Output from Auxiliary Timer 16
P742 468 Fault_REC_TRIG FRT PSL Trigger for the Fault Recorder
P742 469 Battery Fail PSL Input Signal Relay Integrity Front panel Battery Failure
P742 470 Field Voltage Fail PSL Input Signal Relay Integrity 48V Field Voltage Failure
P742 486 Backup Setting PSL Input Signal InterMiCOM Backup setting Alarm
This is an alarm that is ON if any setting fail
during the setting changing process. If this
happens, the relay will use the last known good
setting.
P742 600 CBF I< Start A PSL Output
Signal 50BF Protection Phase A undercurrent CBF Dead Pole Start
P742 601 CBF I< Start B PSL Output
Signal 50BF Protection Phase B undercurrent CBF Dead Pole Start
P742 602 CBF I< Start C PSL Output
Signal 50BF Protection Phase C undercurrent CBF Dead Pole Start
P742 603 CBF I> Start A PSL Output
Signal 50BF Protection Phase A overcurrent CBF Dead Pole Start