background image

05-4055A01, Rev. E

MDS entraNET Technical Manual

183

Model Number: 900

The radio model number. This value is set at the factory and cannot 
be changed.

Serial Number: 1026295

The radio serial number. This value is set at the factory and cannot 
be changed.

Unit Name: Library Admin Office

A name for this radio. It appears at the top of every menu screen.

Owner: Hilltop College MIS

The name of the owner of this radio.

Contact: John Galt X232

The contact person for this radio.

Description: Link to Campus Server

A brief description of this radio.

Location: Hollister Bldg. RM450

The physical location of this radio.

Com2 Port Config: 8N1

The character size, parity type, and number of stop bits to be used.

Max Remotes Allowed: 50

The maximum number of Remotes allowed to connect to this AP.

Device Mode: Access Point

Configures the radio to act as a Remote or an AP. The Access Point 
option is not allowed unless the radio was purchased with it, or an 
Authorization Key was purchased to allow it.

Hop Time: 28

The amount of time that a radio spends at any given frequency. This 
field is controlled by the AP. Remotes obtain the appropriate value 
upon association with the AP.

Network Address: 100

The ID of the network that this radio belongs to. The radio only 
communicates with devices having identical network addresses.

Date Format: Generic

Specifies the date format:

• Generic: dd Mmm yyyy
• European: dd-mm-yyyy
• U.S.A.: mm-dd-yyyy

Console Baud: 19200

The baud rate of the serial menu console. The default value is 
19200 bps.

Summary of Contents for MDS entraNET 2400





























































































































































































































Reviews: