Gaspardo CHRONO 708, Use And Maintenance

Page: 125 / 150

USE AND MAINTENANCE
ENGLISH
-
(1
cod. G19504800
4.10 DISTRIBUTION OF CHEMICAL PRODUCTS
)HUWLOL]HUV DQG LQVHFWLFLGHV DUH GLVWULEXWHG E\ PHDQV RI VSHFLDO
GRVHUV¿WWHGXQGHUWKHFRUUHVSRQGLQJKRSSHUV
4.10.1 MICROGRANULATOR (Accessory)
DANGER!
DANGER OF INHALATION OF HAZARDOUS SUBSTANCES.
POTENTIAL SERIOUS INJURIES OR DEATH.
The micro-granulator involves using microgranular products
that are potentially hazardous for man and the environment; it
LVPDQGDWRU\WRZHDUVXLWDEOH3HUVRQDO3URWHFWLRQ(TXLSPHQW
such as: Rubber or latex gloves, goggles or visors, tyvek
overalls, rubber booties, any active carbon masks.
7KHPLFURJUDQXODWRUKRSSHUVFDQEHDSSOLHGWRWKHSODQWLQJXQLWV
WRGLVWULEXWHIHUWLOL]LQJDQGPLFURJUDQXODWHGLQVHFWLFLGHSURGXFWV
NO liquids
7KHPLFURJUDQXODWRUKRSSHUVDUHFRPSOHWHZLWKDYROXPHWULFGL
VSHQVHUDFWXDWHGE\DQHOHFWULFPRWRUFRQWUROOHGE\WKHVHHGLQJ
PDQDJHPHQWV\VWHP*(1,860$67(5VXSSOLHGZLWKWKHVHHG
drill.
%HIRUHVWDUWLQJWRZRUNLWLVQHFHVVDU\WRFDUU\RXWWKHSURFHGXUH
WRGHWHUPLQHWKH³
calibration factor ´JUDPVUHYWREHXVHGIRU
WKHGLVWULEXWLRQRIWKHSURGXFW
It is advisable to write down the values found in the calibration pro-
cedure and used during work for future uses in the “CALIBRATION
PARAMETERS REMINDER” table (page 127).
4.10.1.1 OPENING REGULATOR
7KH SDVVDJH RI WKH SURGXFW IURP WKH KRSSHU WR WKH YROXPHWULF
GLVSHQVHULVFRQWUROOHGE\DEXONKHDG$)LJZKLFKFDQEH
DGMXVWHGLQSRVLWLRQV
¿J
A
Normally, the bulkheads are set in position 2 (medium opening).
Positions of the opening regulator :
0 ±&ORVHG
1 ±0LQLPXPRSHQLQJIRUORZTXDQWLWLHV
2/3 ±0HGLXPRSHQLQJ
4 ±0D[LPXPRSHQLQJRQO\IRUODUJHTXDQWLWLHV
NOTE : check that all the opening regulators are locked in the
same position.
The quantities dispensed and the homogeneity of distribution
DUHJXDUDQWHHGLIWKHZRUNLQJVSHHGLVZLWKLQWKHLQGLFDWHG
range (s1 and s2) .
7KHUHIRUHLWLVLPSRUWDQWWR¿QGWKHEHVWVHWWLQJEHWZHHQWKHTXDQ
WLW\WREHGLVWULEXWHGDQGWKHZRUNLQJVSHHG
7KLVLVDFKLHYHGE\FRQVLGHULQJWKHUHVXOWLQJZRUNLQJVSHHGUDQJH
VDQGVDFFRUGLQJWRWKH³
calibration factor ´YDOXHH
e
s1 s2
7RFKDQJHWKH³FDOLEUDWLRQIDFWRU´DQGWKHUHIRUHEHZLWKLQDQRSWLPDO
ZRUNLQJVSHHGUDQJHWKHRSHQLQJRIWKHEXONKHDG$)LJPXVW
EHYDULHGDQGWKHFDOLEUDWLRQSURFHGXUHUHSHDWHG
NOTE:
7KHTXDQWLWLHVGLVSHQVHGDQGWKHKRPRJHQHLW\RIGLVWULEXWLRQ
are not guaranteed if the working speed is lower or higher
than the indicated range.
Should you need to work with a speed outside the indicated
range, it is advisable to intervene with the opening of the
bulkhead and repeat the calibration procedure.