Gasboy CFN Series Startup Manual Download Page 43

Page: 43 / 119

Jumpers & Switch Settings

03/07/03

5-5

Pump Control EXPMUX CPU Board

Unlock and open the front door of the pump control unit.

Make sure all override switches are in the

AUTO

position. See Figure 5-1.

Make sure the AC power and battery switches, located in the upper righthand corner of the
power supply are turned

OFF

(down).

Loosen the screw for the card cage section, and swing out the card cage.

Remove the pump control EXPMUX CPU board, located in the rear portion of the card cage,
by pulling on the top white tab.

Figure 5-2. EXPMUX CPU Board

Locate the

jumper patch and install the jumper. This jumper allows battery voltage to the

RAM. It should be installed for normal operation and removed for storage to prevent battery
discharge.

Summary of Contents for CFN Series
























































































































Search results

Summary of Contents for CFN Series

Reviews:

Related manuals for CFN Series

Brands by name

Popular brands

Gasboy CFN Series, Startup Manual

Search results

Summary of Contents for CFN Series

Reviews:

Related manuals for CFN Series

Brands by name

Popular brands