Fujitsu PrintPartner 16V User Manual Download Page 76

Page: 76 / 156

Handling Paper

3. Set the physical paper size

of the MFF.

Use the MFF

paper size menu to select
the size of paper loaded in
the MFF. See the early
section in this chapter.

You can use the printer with the multi-function feeder removed.
This causes no influence on printer operation.

To remove the multi-function feeder, follow these steps:

Notice:

Be sure that the printer is turned off before installing or removing
the multi-function feeder.

Disconnect the feeder cable

and push the two levers at
the bottom of the feeder
upwards to unlock the two

hooks.

2. Then, lift the feeder aslant

toward you to remove it.

User’s Manual

2-29

Summary of Contents for PrintPartner 16V





























































































































































Search results

Summary of Contents for PrintPartner 16V

Reviews:

Related manuals for PrintPartner 16V

Brands by name

Popular brands

Fujitsu PrintPartner 16V, User Manual

Search results

Summary of Contents for PrintPartner 16V

Reviews:

Related manuals for PrintPartner 16V

Brands by name

Popular brands