manualshive.com logo in svg

Fujitsu DL9300, User Manual

Share
Download
Fujitsu DL9300 User Manual Download Page 79

PAPER HANDLING

User's Manual

3-22

2. Locate the tractor unit on the mounting pins as shown below.

Gently push the unit and down until it clicks into position.

(Adjust the letter B labeled on the cut sheet feeder to the letter B

labeled on the printer.)

Installing the tractor unit (for rear feeding)

Left side mounting
pin (from rear)

3. Press the PAPER PATH button to select REAR TRACTOR (the

indicator lights).

4. Set the continuous forms.

Go to step 4~9 in the section Loading Continuous Forms (Front

Feed) in this chapter.

5. Install the rear stacker to its upper or lower position.

NOTE
Do not place the rear stacker under the stacker guides of the
printer.

6. Load the continuous forms.

Go to step 10 in the section 

Loading Continuous Forms (Front

Feed)

 in this chapter.

Summary of Contents for DL9300



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands