manualshive.com logo in svg

Fujitsu DL9300, User Manual

Share
Download
Fujitsu DL9300 User Manual Download Page 164

Options

8-1

User's Manual

INSTALLING OPTIONS

8

INSTALLING OPTIONS

The installation of options allows, you to expand
the capabilities of your printer.  Options available
for the printer include:

• Cut sheet feeder
• Tractor unit

Options can be purchased from your dealer and installed by you.
Order numbers for options are given in Appendix A.

This chapter describes what to do after installing each option.

A cut sheet feeder allows you to automatically feed single sheet.
The SF930 single-bin feeder is available as an option for the 80-column
printer, and the SF940 single-bin feeder for the 136-column printer.
The cut sheet feeder (SF930, SF940) can be mounted on the front or the
rear of the printer.

INSTALLING THE CUT SHEET
FEEDER

Cut sheet feeder

Summary of Contents for DL9300



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands