Fujitsu DL9300 User Manual Download Page 106

Page: 106 / 250

Setup Mode

USING SETUP MODE

User's Manual

5-15

Table 5.3 MENU1 and MENU2 Items and Options

NOTES:
• Underlined options are the factory defaults.
• Asterisks identify items and options that differ for the IBM XL24E and

Epson ESC/P2 emulations. The notes are defined at the end of the table.

MENU1 and
MENU2 Items

Select the same emulation as is selected
in your software. See the section

Selecting an Emulation in

Chapter 2 for

information on selecting an emulation.

Fujitsu DL-series printers
(DPL24C PLUS command set)

XL24E

IBM Proprinter XL24E printers

ESC/P2

Epson printers using the ESC/P2
command set

NOTE: When you change the
emulation, all MENU1 or MENU2
options are reset to the factory
defaults for that emulation.

<FONT>

For each of the following fonts, the
recommended pitch settings are given
after the font name. When you change
the font, be sure to also change the
pitch, if required.

COUR 10
PRSTG12
COMPRSD
BOLDFCE
PICA 10
CORRESP
OCR-B
OCR-A
COUR-N
COUR-B
COUR-I
N.SAN-N
N.SAN-B
N.SAN-I

Options

Description

Summary of Contents for DL9300



























































































































































































































































Search results

Summary of Contents for DL9300

Reviews:

Brands by name

Popular brands

Fujitsu DL9300, User Manual

Search results

Summary of Contents for DL9300

Reviews:

Brands by name

Popular brands