manualshive.com logo in svg

Fujitsu DL9300, User Manual

Share
Download
Fujitsu DL9300 User Manual Download Page 120

Setup Mode

USING SETUP MODE

User's Manual

5-29

Table 5.4  HARDWRE Items and Options (Cont.)

NOTE:  Underlined options are the factory defaults.

HARDWRE
     Items

Options

Description

<BUFFER>

NOTE:

(continued)

• 0BYTE option is recommended

only for graphics application.

• With 96KB selected, the printer

cannot accept any download font
data.

<PIN-18>

N/C:

Does not out put +5V to pin 18 of the
Centronics cable.

+5V

O5V to pin 18 of the
Centronics cable.

<INTRFCE>

Selects the type of the interface to the
computer.

PARALEL

Centronics parallel interface

SERIAL

RS-232C serial interface

AUTO-2S

Auto interface selection mode

AUTO-4S

Both interfaces are ready for

AUTO-6S

communication.

AUTO10S

Specify the timing of regarding the

AUTO15S

selected interface as being inactive.

AUTO20S

Serial Interface Items.  

The following <FORMAT> to <DUPLEX>

items are not printed when you select the PARALEL option for the
<INTRFCE> item.  Be sure that the options selected on the printer
are the same as the options selected using your computer operating
system or your software.  Refer to the documentation provided for
your computer and software.

<FORMAT>

Number of

Number of

data bits

Parity bit

stop bits

8NONE 1

8

None

1

8NONE 2

8

None

2

8EVEN 1

8

Even

1

8ODD 1

8

Odd

1

7EVEN 1

7

Even

1

7ODD 1

7

Odd

1

7MARK 1

7

Mark

1

Summary of Contents for DL9300



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands