manualshive.com logo in svg

Fujitsu DL9300, User Manual

Share
Download
Fujitsu DL9300 User Manual Download Page 25

SETTING UP

2-6

User's Manual

ASSEMBLING THE PRINTER

This section explains how to install the rear stacker and ribbon
cartridge.

Installing the Rear Stacker

The rear stacker enables smooth feeding of both single sheets and
continuous forms.  Install the rear stacker as described below:

1. Referring to the following figure, located stacker guides and

upper and lower stacker grooves at either side of the printer.

2. Locate the front and rear mounting pins on each side of the rear

stacker.

3. While holding the rear stacker at an inclined angle, slide the

front mounting pins into the stacker guides and the rear
mounting pins into the upper stacker grooves.  (Adjust the letter
C labeled on the rear stacker to the letter C labeled on the
printer.  Insert the stacker in the direction of the arrow.)  This is
the rear stacker’s 

up

 position.

Rear stacker

Mounting pins

Upper groove

Stacker guide

Installing the rear stacker (up position)

Summary of Contents for DL9300



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands