manualshive.com logo in svg

Fujitsu DL9300, User Manual

Share
Download
Fujitsu DL9300 User Manual Download Page 138

Setup Mode

USING SETUP MODE

User's Manual

5-47

Checking Vertical Print Alignment (V-ALMNT)

The V-ALMNT function corrects the vertical character displacement
that sometimes occurs with bidirectional printing.  Characters printed
from left to right are not aligned with characters printed from right to
left as shown below:

This example shows how printing looks

 when characters are vertically

misaligned.  Note that the left

 margin is not straight.

If you notice misaligned printing, use the following procedure to
check and correct the vertical print alignment.

Procedure

Make sure that continuous forms paper is loaded in the printer.  If
possible, use forms at least 216 mm (8.5 inches) wide for 80-column
printers or 356 mm (14 inches) wide for 136-column printers to avoid
printing on the platen.  However, you can also use letter or A4 size
forms if you set the WIDTH option in MENU1 to 8 inches.  See the
section 

Changing MENU1 and MENU2 Items and Options

 for details.

Then proceed as follows to check and correct vertical print alignment:

1.

Enter setup mode.

Press the 

↑

MICRO button and the 

↓

MICRO button simultane-

ously until the printer beeps.  Wait for the printer to stop printing
and check that the following <<FUNCTION>> menu is printed:

<<FUNCTION>>

SAVE&END

MENU1

MENU2

HARDWRE

ADJUST

CONFIG

DEFAULT

LIST

SELF-TST

HEX-DUMP

V-ALMNT

GAP-ADJ

Summary of Contents for DL9300



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands