manualshive.com logo in svg

Fujitsu DL9300, User Manual

Share
Download
Fujitsu DL9300 User Manual Download Page 144

Setup Mode

USING SETUP MODE

User's Manual

5-53

ONLINE SETUP MODE

The preceding sections describe offline setup mode.  This section
introduces online setup mode.  The tedious task of setting up printer
features one-by-one from the control panel and printing and checking
the desired options on paper can be avoided by using online setup
mode.  In online setup mode, printer features are set via the computer
rather than the printer control panel.

Put the printer in online setup mode, in either of the following two
ways:

• Turn the printer off and then turn the printer back on while

pressing the TEAR OFF button.  Hold down the button until
the printer beeps.

• Issue the printer command ESC e ONLINE.  This command

is valid in any emulation.

Send setup data from the computer in any of the following three
ways:

• Enter setup data directly from the computer keyboard

before starting your job.  With MS-DOS, hold down the Ctrl
key and type P.  Data entered from the keyboard is sent
directly to the printer.  When data entry is complete, hold
down the Ctrl key again and type P.  This method is useful
when just a few settings need to be changed.

• Use an editor program to prepare a setup data file and then

send the file to the printer using a command before starting
your job.  With MS-DOS, use the COPY command.  This
method is useful when settings are used repeatedly.

• Write a program that enables interactive entry of setup data

on the CRT screen.  This method is the most useful of the
three.  This printer is provided with a floppy disk which
contains this program called DLMENU.  For DLMENU, see
the last section of chapter 2.

To exit from online setup mode, send EXIT as the last setup data.

For details of setup data and its format, refer to the programmer’s
manual for each emulation.

Summary of Contents for DL9300



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands