manualshive.com logo in svg

Fujitsu DL9300, User Manual

Share
Download
Fujitsu DL9300 User Manual Download Page 52

Setting Up

SETTING UP

User's Manual

2-33

4. Use your software printer selection menus or the printer setup

mode (described in Chapter 5) to make required changes in the
page layout or other print features.

If the printer does not print or prints the wrong characters,
proceed as follows:

• Make sure that the interface cable is properly connected.

• Make sure that the printer emulation selected in your

software is the same as that selected on the printer.

• If you are using a serial interface, make sure that the printer

serial interface settings are the same as those on the compu-
ter.  The printer’s preselected factory settings are 8 data bits,
no parity, 1 stop bit, 9600 baud, and XON/XOFF protocol.

You can change the serial settings on either the printer or
your computer.  To change the printer settings, see Chapter
5.  To change the computer settings, use the selection menus
provided by your software or the commands of your
computer operating system.  The following example uses the
MS-DOS operating system:

Summary of Contents for DL9300



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands