manualshive.com logo in svg

Fujitsu DL9300, User Manual

Share
Download
Fujitsu DL9300 User Manual Download Page 78

User's Manual

Paper

Handling

PAPER HANDLING

3-21

10. Put the rear stacker in its down position.

11. Press the LOAD button to advance the paper to the top-of-form

position.  Top-of-form is the first line on which printing can
start.  After loading paper, the printer goes into online mode.

12. Print a sample page and check the page margins.  Make the

following adjustments, as necessary:

• Horizontal alignment.  Move the forms tractors as required.
• Top-of-form setting (see Chapter 5).
• Margin settings.  Use your software or the printer setup

mode (see Chapter 5).

NOTE
Do not open the front cover during printing.

Loading Continuous Forms (Rear Feed)

A tractor is supplied as standard and is attached to the front of the
printer.  It can be attached to the rear of the printer.  You can also buy a
tractor unit as an additional rear tractor unit.
A maximum of 6-ply media can be fed from the rear tractor unit.

• Put the paper table in the normal mode when the rear tractor

unit is to be used.

To reinstall the tractor unit for rear feed:

1. Slide the rear stacker  horizontally to remove it from the printer.

Summary of Contents for DL9300



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands