manualshive.com logo in svg

Fujitsu DL9300, User Manual

Share
Download
Fujitsu DL9300 User Manual Download Page 110

Setup Mode

USING SETUP MODE

User's Manual

5-19

MENU1 and
MENU2 Items

Table 5.3  MENU1 and MENU2 Items and Options (Cont.)

NOTES:
• Underlined options are the factory defaults.
• Asterisks identify items and options that differ for the IBM XL24E and

Epson ESC/P2 emulations.  The notes are defined at the end of the table.

Options

Description

<PAGE LG>

Specifies the length of the page in
inches.

## IN

For DPL24C PLUS and IBM XL24E

emulations:

3.0, 3.5, 4.0, 5.0, 5.5, 6.0, 7.0, 8.0, 8.5,
11.0 (letter size), 11.6 (A4 size), 12.0,
14.0, or 18.0 inches

For Epson ESC/P2 emulation:

4.0, 4.5, 5.0, ..., 11.0, 11.5, ...,
22.0 inches

<LFT-END>

Specifies the print start column for
changing the left margin.  Printing
starts at the position given by this
column plus your software-
specified left margin.

## COLM

Column 1, 2, 3, ..., 41

LET-END

Software-
specified
margin

Summary of Contents for DL9300



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands